Watec WAT-910BD Скачать руководство пользователя страница 38

Страница: 38 / 65

WAT-910BD H/W MANUAL

Please do not change the bit or the byte data with the notation of "-" among following tables.

(Camera operation will not be guaranteed.)

The default value can be found in

red underlined

(or, with notation of default) in the table.

0x09:OFF(E:1/60,C:1/50), 0x0A:FL, 0x0B:1/250,

*1:When switching to EI（Electronic Iris　mode), it is recommended be used "FIX SHUTTER SPEED" parameter.

6.4 CAMERA PARAMETER

－

actual AGC MID MAX(dB) = ( [0x05 … 0xFF] * 4 * 0.035 ) + 5.3 (default:

0xD0

, approx.34.5(dB))

1:ON

0x10:1/10000, 0x11:1/100000

－

0:OFF

Bit

－

(*1)

Address

0x400

－

0x403

－

0x405

－

0x407

－

0x409

－

0x408

－

0x40B

－

0x40A

－

0x40D

－

0x40C

－

0x40E

－

0x40F

－

FIX SHUTTER SPEED

0x00:x256, 0x01:x128, 0x02:x64, 0x03:x32, 0x04:x16,

0x05:x8, 0x06:x4, 0x07:x2,

0x08:EI

0x0C:1/500, 0x0D:1/1000, 0x0E:1/2000, 0x0F:1/5000,

－

0x410

－

(notice 2) Be sure to set large value than AGC MIN.

(notice 1) Be sure to set 5 or more large values.

－

actual AGC LOW MAX(dB) = ( [0x05 … 0xFF] * 4 * 0.035 ) + 5.3 (default:

0xB0

, approx.30(dB))

(notice 1) Be sure to set 5 or more large values.

(notice 2) Be sure to set large value than AGC MIN.

0x402

－

0x404

－

AGC MODE

0x401

－

0x00:OFF

0x01:LOW

0x02:MID

0x03:HI

－

actual AGC HI MAX(dB) = ( [0x05 … 0xFF] * 4 * 0.035 ) + 5.3 (default:

0xFF

, approx.41(dB))

(notice 1) Be sure to set 5 or more large values.

－

0x413

AGC LOW MAX

0x412

AGC MID MAX

－

0x411

AGC HI MAX

1:ON

SENS UP MAX

0x00:x2, 0x01:x4,

0x02:x8

0x06:x128, 0x07:x256(FLD)

0x03:x16, 0x04:x32, 0x05:x64,

FUNCTION

0x406

－

SENS UP

0:OFF

(notice 2) Be sure to set large value than AGC MIN.

- 35 -

Содержание WAT-910BD


































































Результаты поиска

Содержание WAT-910BD

Отзывы:

Похожие инструкции для WAT-910BD

Бренды по названию

Популярные бренды

Watec WAT-910BD, Руководство по оборудованию

Результаты поиска

Содержание WAT-910BD

Отзывы:

Похожие инструкции для WAT-910BD

Бренды по названию

Популярные бренды