Watec WAT-910BD Скачать руководство пользователя страница 10

Страница: 10 / 65

WAT-910BD H/W MANUAL

4.3 DC IRIS LENS CONTROL

This connector is used to connect a DC IRIS LENS.

When connecting the lens, be careful to wire after

confirming the pin assignments.

(1) Wiring to the lens

Pin assignments of JEITA standard iris connector

and J3 connector terminal have one-to-one

correspondence as following.

(2) Adjustment method of the lens iris

The lens iris is adjusted with next steps.

STEP1: Fix the shutter speed by using OSD menu.(SETUP->EXPOSURE->SHUTTER)

Recommended setting of SHUTTER is either OFF(EIA:1/60,CCIR:1/50) or FL(EIA:1/100,CCIR:1/120).

STEP2: Turn off "SENSE UP" function.

STEP3: Turn off "AGC" function.

Set "GAIN" to the minimum value (6dB) by using "MANUAL GAIN" menu.

STEP4: Return to the EXPOSURE menu, by adjusting the VR1, set the proper lens iris.

STEP5: If the adjustment of lens iris is correct, when AGC is switched to LOW from OFF, the video signal

will be a little brighter.

STEP5: When switching to AGC LOW from OFF, and the video screen is to be slightly

STEP1,2: OSD SETTINGS

brighter, it is the proper result of lens iris adjustment.

(Fig.4-5) Pin assignments of DC IRIS connector

　Sense＋

STEP3: MANUAL GAIN SETTING

STEP4: IRIS ADJUSTMENT

　Drive－

　Sense－

female IRIS connector(JEITA spec.)

Pin Name

②

Parts Shape(Pin No.)

③

④

　Drive＋

①

J3: IRIS Connector(for DC IRIS LENS)

VR1: Adjustment VR(for DC IRIS LENS)

① ② ③ ④

open

- 7 -

Содержание WAT-910BD


































































Результаты поиска

Содержание WAT-910BD

Отзывы:

Похожие инструкции для WAT-910BD

Бренды по названию

Популярные бренды

Watec WAT-910BD, Руководство по оборудованию

Результаты поиска

Содержание WAT-910BD

Отзывы:

Похожие инструкции для WAT-910BD

Бренды по названию

Популярные бренды