background image

V3.8 | EN | 17.05.23

13

Single gas detector

PDM 

Single gas detector

PDM 

9. LIMITED WARRANTY

WatchGas warrants this product to be free of defects in workmanship and materials-under nor-

mal use and service-for two years from the date of purchase from the manufacturer or from the 

product’s authorized reseller.

The manufacturer is not liable (under this warranty) if its testing and examination disclose that 

the alleged defect in the product does not exist or was caused by the purchaser’s (or any third 

party’s) misuse, neglect, or improper installation, testing, or calibrations. Any unauthorized at-

tempt to repair or modify the product, or any other cause of damage beyond the range of the 

intended use, including damage by fire, lightening, water damage or other hazard, voids liability 

of the manufacturer.

In the event that a product should fail to perform up to manufacturer specifications during the 

applicable warranty period, please contact the product’s authorized reseller or WatchGas service 

center at [email protected] for repair/return information.

WatchGas 

Klaverbaan 121

2908 KD Capelle aan den IJssel

The Netherlands

FOR MORE INFORMATION

www.watchgas.com

[email protected]

Содержание PDM














Отзывы: