8
FIGURE 2
VEND
PRICE
COIN SLOTS
1 2 3 4 5 6 7 8
10 c
0
25 c
35 c
50 c
60 c
75 c
85 c
$1.00
$2.00
$1.10
$1.25
$1.35
$1.50
$1.60
$1.75
$1.85
TABLE OF VEND PRICE
Note:
If the slide mechanism has already been installed, skip this step.
Install Coin Slide
1. Remove the access panel from the top of the meter case by
unlocking the service lock with the key taped to the front of
the coin box.
2. Deposit coins in the coin slide and push the coin slide all the
way in. Hold coin slide in extended position and insert through
opening in he front of the meter case.
3. From inside the meter case, place the threaded end of the bolt
through the center mounting hole in the front of the meter
case.
4. While holding the bolt in place, guide the coin slide
mechanism onto the threads and into the guide holes
in the front of the meter case.
5. Tighten the bolt as you guide the coin slide mechanism into
place.
6. Tighten the bolt using a ratchet and a 5/8-in. socket until the
slide mechanism is secure and does not move.
COIN BOX ADJUSTMENT
The tight fit of the money box is set at the factory. Customer may
loosen fit as desired by loosening the slotted nuts. See FIG.2.
Keep A record of all coin-box key numbers.
A lost key can only be replaced by ordering the key numbers
from the place were the unit was purchased. The key number is
located both on the key and behind the end panel of the coin
box. If the key number is not available, the lock must be drilled
out to remove the coin box.
8
Changing Vend Price
Note: Place all screws and other items removed from coin slide
assembly on a cloth so they will not get lost.
Electical Shock hazard
. Disconnect power before
servicing. Replace all parts and panels before operating. Failure to
do so can result in death or electrical shock.
1. Unplug washer or disconnect power.
2. Remove slide mechanism from meter
case.
3. Remove slide return spring.
4. Place coin(s) in coin slot(s) and push
forward all the way.
5. Remove buffer.
6. Turn coin chute upside down and
install or remove required number of
block-out keys. Remove keys to
increase vend, add keys to lower vend.
7. Reasemble buffer.
8. Pull slide back to original position and
reassemble slide return spring.
9. Set new vend price by adding or removing
the appropriate block-out keys and/or
dime inserts according to Table of Vend
Prices.
NOTES:
•
Black slots are closed out by block-out key. To remove block-out
keys, pull straight up.
•
Be sure block-out keys and/or dime inserts are seated properly
and ratchet dog is in place with its spring connencted. Be sure
the proper coin sizing block is in place.
10. Plug in washer or reconnect power.
REPLACEMENT PARTS
If replacements parts are needed for your washer, contact the source
where you purchased your washer or call 516-371-0700 for the
Wascomat Authorized Parts Distributor nearest you. For coin box
parts, call 1-800-221-0982, Greenwald Industries.
Destroy the carton and plastic bags after the washer is
unpacked. Children might use them for play. Cartons covered with
rugs, bedspreads, or plastic sheets can become airtight chambers
causing suffocation. Place all materials in a garbage container or
make materials inaccessible to children.
The instructions in this manual and all other literature
included with this washer are not meant to cover every possible
condition and situation that may occur. Good safe practice and
caution
MUST
be applied when installing,operating and maintaining
any appliance.
Maximum benefits and enjoyment are achieved when all the Safety
and Operating instructions are understood and practiced as a
routine with your laundering tasks.
