4
GROUNDING REQUIREMENTS
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock. Check with a licensed
electrician if you are in doubt as to whether the appliance is properly
grounded.
1.
The washer
MUST
be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electrical shock by a
path of least resistance for electrical current.
2.
Since your washer is equipped with a power supply cord having
an equipment-grounding conductor and a grounding plug, the
plug
MUST
be plugged into an appropriate, copper wired
receptacle that is properly installed and grounded in accordance
with all local codes and ordinances or in the absence of local
codes, with the National Electrical Codes, ANSI/NFPA 70 (latest
edition). If in doubt, call a licensed electrician.
DO NOT
cut off or alter the grounding prong on the power supply
cord. In situations where a two-slot receptacle is present, it is the
owner’s responsibility to have a licensed electrician replace it with a
properly grounded
three prong grounding type receptacle.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets
MUST
be installed within 42 inches (107
cm) of your washer’s water inlet. The faucets
MUST
be 3/4 inch (1.9
cm) garden hose type so inlet hoses can be connected. Water pressure
MUST
be between 10 and 120 pounds per square inch (maximum
unbalance pressure, hot vs. cold, 10 psi.) Your water department can
advise you of your water pressure.
4
Max.
Max.
Max.
Max.
Max.
DRAIN REQUIREMENTS
Models equipped with drain pump:
1.
Drain
MUST
be capable of eliminating 17 gals (64.3 L) per minute.
2.
A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
3.
The standpipe height above the floor should be:
NOTE:
Drain hose attached to the washer can reach a 58 in. (147 cm) high
standpipe. For higher standpipe use hose P/N 131461201, available
from an authorized parts distributor. If drain is less than 24 in. (61
cm), install a siphon break kit, available at your local hardware store.
Models equipped with gravity drain:
1.
Floor drain
MUST
be capable of eliminating 17 gals (64.3 L) per
minute.
2.
Floor drain diameter must be at least 1/2 inch larger than drain
hose.
LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside weather
conditions. The ambienttemperature should never be
below 60 degrees F (15.6 degrees C) for proper washer operation.
2. In an area where it will come in contact with curtains or drapes.
3. In an area (garage or garage-type building) where gasoline of
other flammables are kept or stored (including automobiles).
4. On carpet. Floor
MUST
be solid with a maximum slope of 1/2 in.
per foot (1.27 cm per 30.5 cm). To ensure vibration or
movement does not occur, reinforcement of the floor may be
necessary.
IMPORTANT MINIMUM INSTALLATION CLEARANCES
When installed in alcove: Sides, Rear, Top = 0 in (0 cm).
When installed in closet: Sides, Rear, Top = 0 in (0 cm),
Front = 1 in (2.54 cm).
Closet door ventilation openings required: 2 louvers each 60 in
²
(387
cm²) -
3 in (7.6 cm) from top and bottom of door.
PRE-INSTALLATION REQUIREMENTS
Tools Required for Installation:
1.
1/4 in. nut driver
2.
3/8 in. socket with ratchet.
3.
3/8 in. open end wrench.
4.
7/16 in. socket with ratchet.
5.
9/16 in. open end wrench.
6.
Channel-lock adjustable pliers.
7.
Carpenter’s level.
ELECTRICAL REQUIREMENTS
CIRCUIT
- Individual, properly polarized and grounded 15 amp. branch
circuit fused with 15 amp. time delay fuse or circuit breaker.
POWER SUPPLY
- 2 wire, with ground, 120 volt, single phase, 60 Hz,
Alternating Current. NOTE: The use of this washer with power created
by gas powered generators, solar powered generators, wind powered
generators or and other generator other than the local utility company
is not recommended.
OUTLET RECEPTACLE
- Properly grounded 3-prong receptacle to be
located so the power supply cord is accessible when the washer is in
an installed position. NOTE: GFI (Ground Fault Interrupter) receptacle
is not required.
