background image

 

 

 

 

 

Assemble on a soft level surface to 

avoid damaging the unit or your 

floor.

Do not overload the drawers.

 Do not use a power

 

 

drill/screwdriver for 

inserting screws, as it

 can cause screws to

 break or strip.

 

 

 

Clean with mild soap on a damp

 

soft rag. Rinse and dry 
thoroughly. Do not use abrasive 
chemicals for cleaning.

Please check if there any loose screws
on the unit from time to time.

This product should not be 
discarded with household waste. 
Take to your local authority waste

 

 

disposal centre.

 

 

 

 

 

1

2

Do not allow your children to stand or

 climb on or in the drawer. It could 

make it top-heavy and cause the 

unit to damage or tip over. 

Assemble the item as close to its 

final position (in the same room) as 

possible. 

Do not place furniture directly infront

 

 

of radiators, fires or any other 

source of heat. 

Check that if you have all the 

components andools listed on the

 

 

front coverand pages 2. 

Emove all fittings from the plastic 

Obags and separate them into 

their groups. 

 Keep children and animals away 

from the work area, small parts 

could choke if swallowed. 

 Make sure you have enough 

space to layout the parts before 

stating. 

Regular dusting with a dry cloth will 
keep your units
Clean marks with a damp cloth.
Do not allow spillages to stay on the 
surface
To remove stubborn stains, wipe with a 
damp cloth and washing up

Do not use abrasive cleaners.
Do not clean with products contaiing the 
following: Acetone, (e. g nail varnish 
remover). Ammonia (e. g. bleach). 
orSodium hydroxide (e. g. Caustic soda, 
drain and oven cleaners).

In the event of accidental contact with 
aggresive cleaners, rinse thoroughly with 
water.
To remove stains and small scratches 
use a car polish or light cutting com-
pound.
Use place mats to protect the surface 
from moisture and heat.

Safety Notes and Care Avice

Important – Please read these instructions fully before starting assembly

General care and maintenance

Cleaning and care of high gloss surfaces

Parts of the assem-

ble will be easier 

with 2 people.

Dispose of all packaging carefully 

and responsibly.

MANUFACTURERS:GUANGZHOU HOMY CASA CO,.LTD.
Add.:705-1,BUILDING NO.2,134 XIHUA ROAD,LIWAN DISTRICT,GUANGZHOU,CHINA
Contact:Tracy Tel:+8618680277793 E-Mail:[email protected]

8

Содержание ZZ001










Отзывы: