Warrior Winches 80SPS12 Скачать руководство пользователя страница 2

1

INTRODUCTION

Congratulations on your purchase of a winch.  We design and build winches to strict 

specifications and with proper use and maintenance should bring you years of 

satisfying service.  

WARNING

 - 

Read, study and follow all instructions before operating this 

device.  Failure to heed these instructions may result in personal injury 

and/or property damage. 

Your winch can develop tremendous pulling forces and if used unsafely or 

improperly could result in property damage, serious injury or death.  Throughout 

this manual you will find the following symbols for caution, warning and danger.  

Pay particular attention to the notes preceded by these symbols as they are 

written for your safety. Ultimately, safe operation of this device rests with you, the 

operator. 

Indicates a potentially hazardous situation which, if not avoided, may result in 
minor or moderate injury.  This  notation is also used to alert against unsafe 
practices. 

Indicates a potentially hazardous situation which, if not avoided 
could result in death or serious injury. 

CAUTION

WARNING

Содержание 80SPS12




















Отзывы: