background image

©2019 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. 

107229A0 

 

INSTALLATION INSTRUCTIONS 

Ascent-HD Front Bumper 

Part Number: 10718X 

Application: 2017-20 Ford SD F450/F550 

G E N E R A L S A F E T Y P R E C A U T I O N S 

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have 

provided installation and operating instructions and other information on labels and in this guide. This information 

alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards 

associated with this product, you must use your own good judgment. 

CARELESSINSTALLATION AND OPERATIONCANRESULTINSERIOUSINJURY OR EQUIPMENTDAMAGE. READ AND 

UNDERSTANDALLSAFETYPRECAUTIONSANDOPERATINGINSTRUCTIONSBEFOREINSTALLINGANDOPERATING 

THIS PRODUCT. 

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury 

or death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean: 

WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.  CAUTION 

signals a hazard that may cause minor to moderate injury, if you do not follow recommendations. 

This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general 

information worthy of special attention. 

 

 

W A R N I N G 

IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD 

Failure to observe these instructions could lead to severe injury or death 

 

Always 

Know Your Winch. Take time to fullyreadtheInstructionsand/orOperationsGuide,and/orBasicGuidetoWinchingTechniques,inorderto understand your winch and its operations. 

 

Never 

work under vehicle before properly securing vehicle. 

 

Always 

use appropriate and adequate care in lifting components into place. 

 

Never 

work under vehicle before properly securing vehicle. 

 

Always 

use appropriate and adequate care in lifting components into place. 

 

Never 

use a jack to support the vehicle. 

 

Always 

use jack stands in pairs to support the vehicle. 

 

Always 

use jacks or jack stands only on a hard, stable, and level surface. 

 

Never 

exceed the rated capacity of a jack or jack stands. 

 

Always 

verify that the parking brake is set, the transmission is in park(automatic)or reverse(manual)and the rear wheels are blocked before working on vehicle. 

 

Never 

work under vehicle before properly securing vehicle. 

 

Always 

use appropriate and adequate care in lifting components into place. 

 

Always 

insure components will remain secure during installation and operation. 

 

Always 

tighten all nuts and bolts securely, per the installation and operation. 

 

Always 

perform regular inspections and maintenance on the winch, winch mount and related hardware. 

 

Always 

replace all worn or damaged parts before operating. 

 

Never 

operate this WARN product with damaged or missing parts. 

 

Always 

use extreme caution when drilling on any vehicle. Make sure that all fuellines,brakelines,electricalwires,andotherobjectsarenotpuncturedordamagedwhen/ if drilling on the vehicle .Thoroughl y 

inspect the area to be drilled(on both sides of material)prior to drilling, and relocate any objects that maybe damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical 

shock, fire or personal injury. 

 

Always 

use extreme caution when cutting and trimming during fitting. 

 

Always 

wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause eye injury. 

 

Always 

remove jewelry and wear eye protection. 

 

Never 

lean over battery while making connections. 

 

Never 

route electrical cables across any sharp edge, through or near moving parts, near parts that become hot. 

Read installation and operating instructions thoroughly. 

 

WARN INDUSTRIES, INC. 12900 S.E. Capps Road, 

Clackamas, OR USA 97015-8903, 1-503-722-1200, FAX: 1-503-722-3000 

Customer Service: 1-800-543-9276 

Dealer Locator Service: 1-800-910-1122 

International Fax: 1-503-722-3005 

Содержание Ascent-HD 10718X









Отзывы: