Warn 685000 Скачать руководство пользователя страница 50

Страница: 50 / 51

986765A1.doc Page 49 of 50

Motor does not run.

Faulty Trigger Switch

Defective Motor

Repair or replace Switch

Replace Motor

Loose connection of the
Wires to be Motor terminals.

Secure the Motor terminal and
Wires.

1.6   Electrical sparks
        appear around
       Motor.

Switch held in power-in
position while PullzAll is
stalled.

Replace Wiring harness PullzAll
Motor.

1.7   Wiring harness
       insulation has
        melted.

Poor installation caused Wire
insulation to be rubbed off or
cut, causing direct short.

Replace Wiring harness.

1.8   PullzAll makes
       squeaking / high
       pitch noise.

Drum Bushing not lubricated.

Grease Drum Bushings.

1.10 Malfunctioning

Not operating correctly.

Cease operation. Diagnose, Repair
or Replace.

INSPECTION

VISUAL INSPECTION:

•

While disconnecting the connectors, never pull the wiring Harnesses. Unlock the connector
first and then pull them apart by holding connectors themselves.

•

While connecting connectors, also hold connectors and put them together until they lock
securely (a click is heard).

•

While Installing the Wiring Harness, fix it with clamps so that no slack is left.

•

While using a tester for checking continuity or measuring voltage, be sure to insert the tester
probe from the wire harness side.

Содержание 685000




















































Результаты поиска

Содержание 685000

Отзывы:

Похожие инструкции для 685000

Бренды по названию

Популярные бренды

Warn 685000, Руководство по обслуживанию

Результаты поиска

Содержание 685000

Отзывы:

Похожие инструкции для 685000

Бренды по названию

Популярные бренды