background image

 

 

Installation Instructions for 92600 
ATV Winch 

3000 lb. Rated Pull 

 

SPECIFICATIONS 

Rated line pull: 3000 lbs. (1360kgs) single line 
Motor: Permanent magnetic DC 12V with 1.2 hp. /0.9kw output 
Gear: Differential planetary 
Gear ratio: 153 : 1 
Wire rope: 3/16

” x 41’ ( 4.8mm x 11m) 

Drum size: 1.25

” x 2.86” ( 31.75mm 72mm) 

Dimensions: L x W x H ( 300mm 105mm 105mm) 
N W.: 7.5 kg 
G.W.: 11 kg 
 

Line speed and motor current (first layer) 

Line pull 

Lbs. 

1000 

2000 

3000 

Kgs 

454 

907 

1360 

Line speed 

FPM 

9.5 

6.6 

3.6 

2.3 

MPM 

2.8 

2.0 

1.1 

0.7 

Motor current 

Amps 

12 

60 

90 

150 

 

Line pull and cable capacity 

Layer of cable              

 

 

Rated line pull per layer 

Lbs.  3000  2320  1890  1590  1380 

Kgs  1360  1052 

858 

720 

620 

Cable capacity per layer 

Ft. 

4.9 

11.5 

19.3 

28.5 

32 

1.5 

3.5 

5.9 

8.7 

10 

 

INTRODUCTION 

Congratulations on your purchase of a JEGS winch. Designed and built to strict specifications. With proper use and 
maintenance your winch should bring you years of satisfying service.  
 

WARNING

 - Read, study and follow all instructions before operating this device. Failure to heed these instructions may 

result in personal injury and/or property damage. 
 
Your winch can develop tremendous pulling forces and if used unsafely or improperly could result in property damage, 
serious injury or death. Ultimately, safe operation of this device rests with you, the operator.  
 

CAUTION

 Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This 

notation is also used to alert against unsafe practices.  
 

WARNING

 Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. 

 

                                         1-800-345-4545   jegs.com

 

Содержание 92600












Отзывы: