background image

WARN INDUSTRIES 

PAGE 1 

63289 Rev B2 

 

 

 

 

 

 

 

 

INSTALLATION INSTRUCTIONS

 

ATV PLOW

 

Mount Kit:  PN 63290 

Application: 2000+ HONDA RANCHER 

 

 

 
 

 

WARNING 

SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF THE FOLLOWING. 

 

Always read the Plow Operator’s Manual, the Winch Operator’s Manual, and all warning labels 
before operating or using your ATV plow.  

 

Always operate ATV at a walking speed with the blade installed.  Do Not exceed 5mph  (8 km/h) 
even with the blade up. 

 

Always plow CAUTIOUSLY, impact with a hidden or stationary object may cause the ATV to 
stop suddenly or go out of control. 

 

Never operate the ATV on slopes greater than 10° with the plow installed. 

 

Never stand or ride on the plow. 

 

Always stay clear of moving parts and joints.  Keep others away when operating or adjusting 
plow. 

 

Always inspect the plow mechanism, fasteners, cable, and adjustments before operating.  Replace 
all worn or damaged parts before operating. 

 

Always lower the plow to the down position before leaving the ATV unattended.

 

 

 
 

TOOLS REQUIRED 

Ratchet 

Sockets:  7/16, 1/2, 9/16 

Wrenches:  7/16, 1/2, 9/16 

Drill with 5/16” bit (

2002 or newer models only

Phillips Screwdriver (optional) 

 

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have 
provided installation and operating instructions and other information on labels and in this guide. This information alerts you 
to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with 
this product, you must use your own good judgment.

  

CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT 
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS 
BEFORE INSTALLING AND OPERATING THIS PRODUCT. 

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or 
death. 

WARNING

 and 

CAUTION

 are signal words that identify the level of hazard. These signal words mean:  

 WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations. 

CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.

  

This guide uses 

NOTICE

 to call attention to important mechanical information, and 

Note:

 to emphasize general information 

worthy of special attention. 

Содержание 63290






Отзывы: