background image

©2019 Warn Industries, Inc. WARN® and the WARN logo are trademarks of Warn Industries Inc. 

10 

106532A1

I N S T A L L A T I O N   I N S T R U C T I O N S

CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDER-

STAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.

M A I N T E N A N C E   /   C A R E

1.  Inspect all parts on the winch, winch mount, and related hardware prior to each use.  Replace all hardware that appears rusted 

or deformed.

2.   Inspect all nuts and bolts on the winch, winch mount, and related hardware prior to each use.  Tighten all nuts that appear to be 

loose.  Stripped, fractured, or bent bolts or nuts need to be replaced.

3.   Check all cables prior to use.  Replace cables that look worn or frayed.

4.   Check all moving or rotating parts.  Remove debris that may inhibit the part from moving freely.

37.  Reinstall the bumper cover over the mounting kit (reverse 

removal steps).  

NOTE:  Be sure to check for any areas of 

contact between the bumper cover and winch mount and 

trim as needed.

38.  Reinstall the wheel well push clips and all of the fasteners 

along the top edge of the grille. 

39.  Reinstall the plastic clips along the bottom of the bumper 

where possible, the center clip locations were removed 

with the center of the bumper cover.

40.  Install plastic plugs (B4) if not installing the optional Bolt 

on Grille Guard Kit.  

41.  Plug in factory fog lights if equipped.

42. 

OPTIONAL

: Mount license plate using hardware (B2) and 

(B3).

Installation is complete.

Figure 22

Содержание 106413











Отзывы: