Warmlite WL44018, Инструкция по эксплуатации

Страница: 7 / 12

7 www.warmlite.co
BEFORE YOUR FIRST USE:
1. Remove your appliance from the packaging.
2. Keep the front of the appliance through which
the heat is radiated at least one meter away from
furniture, curtains and other flammable objects at
all times.
3. Ensure there is a grounded socket nearby (back of
the appliance).
4. Never use an extension lead. The main cable must
remain at the back of the appliance and must not
be in contact with any hot elements.
5. Your appliance is now ready for normal use.
6. Dispose of the packaging in a responsible manner.
USING YOUR APPLIANCE:
Turning the unit On and Off:
1. To power the unit on, first plug it into an active
mains socket. The pilot light on the unit’s control
panel will come on to indicate the unit is plugged
in.
2. Once the unit has been plugged into the mains,
turn the heat selection dial to any position other
than 0 and the thermostat dial clockwise, away
from the ‘-‘ position, to turn it on. The temperature
dial will give off a clicking sound and air will start
emitting from the front grille to show the unit is in
operation.
WARNING! DO NOT touch the grille while the heater in
operation, as it will be very hot and there will be a risk
of burns.
3.
To power the unit off, turn the heat selection dial
to the 0 position and the thermostat dial counter-
clockwise to the ‘-‘ position. The temperature
dial will give off a clicking sound and air will stop
emitting from the front grille to show the unit has
been powered down.
WARNING!
DO NOT store the unit directly after turning
it off. Allow for time for the unit to cool down before
storing.
Mode Selection:
• This heater offers a choice of 2 heat settings - Low
(I) and High (II.
• Turn the mode selection dial counter-clockwise to
cycle between Off (0), Flame, Low and High heat
settings. Turn this dial clockwise to cycle between
High heat, Low heat, Flame and Off (0) settings.
• Turn the heat selection dial to the 0 position to turn
the unit off.
Heat Selection:
• This heater is equipped with an adjustable
thermostat, which allows for temperature control
within each of the 2 heat settings.
• Use the thermostat dial to manually increase
or lower the heating temperature. Turn this dial
clockwise away from the Off position to increase
the temperature, or counter-clockwise towards the
Off position to decrease it.
CHECK THAT YOU HAVE NOTED ALL THE
FOLLOWING INSTRUCTIONS:
• Never leave children unsupervised in a room where
the fire is ON and unguarded.
• Never obstruct or cover the fan outlet or force
items into the fire openings.
• Never install or use the fire anywhere where water
is in use, i.e. bathrooms, kitchens, shower rooms,
swimming pools etc.
• Never use aerosols or steam cleaners on or
around the fire.
• Never route the mains supply cable under carpet
etc.
• Never install the fire close to curtains or
combustible materials.
• Never use the fire to dry clothes etc.
• Never sit or stand on the fire.
• Never cut the off the plug and hard wire into a
fixed fused spur.
NOTE: When the fire is turned on for the first time
or when it has not been used for some time, it may
release a slight, harmless odour. This odour is a normal
occurrence caused by the initial heating of the internal
heating elements or dust, and will disappear with use.
TROUBLE SHOOTING
Safety Cut-Out devices:
To ensure against the potential hazard caused by
blockage of the air outlet, this unit is equipped with an
automatic overheat safety cut-out device and a built-in
tip over switch. When the device is activated the heater
will not operate. If this occurs, the unit can be reset using
the following procedure.
1.
Turn the fire off by depressing the on/off switch on
the unit.
2. Unplug the power cord form the electrical mains
supply socket and leave it disconnected for at
least 15 minutes.
3. Ensure that the air vents are free from obstruction.
4. Plug the power cord back into the mains socket.
5. Turn the fire back on.
6. If the fire fails to operate, check the fuse in the
plug.
7. If the fuse in the plug is OK and the fire is still not
functioning, contact a qualified person.