8
9
BEFORE BLENDING
1. Before starting, make sure that the blender is unplugged and container
is not positioned on the blender.
2. Put ingredients into container and cover it. Do not fill above MAX fill line.
3. Place container on blender base. Be sure container is fully seated
and that the drive coupling is properly engaged. Place the lid and dasher
on the jar followed by the Ellipse drive. Plug blender cord into outlet.
XTREME CONTROL SETTINGS
1. The motor speed can be adjusted by pressing the
or
speed buttons. Speed ranges from
5% to 100%.
100%
20,000 RPM
50%
10,000 RPM
5%
1,000 RPM
The Speed Up
button will increase the motor speed display in 1%
increments, and the Speed Down
button will decrease the motor speed
in 1% increments. Holding down either button will quickly scroll through
speeds.
Using the Speed Up
and Speed Down
buttons, set desired motor
speed. If no speed is selected, motor will default to 100%.
NOTE:
The motor does not run at the newly set speed until the START/
STOP
button is pressed. If START/STOP
button is not pressed
within 5 seconds, the new speed setting will be stored for next use and
the blender will return to STANDBY mode; the display will once again
read “PRESS ANY BUTTON TO BLEND.”
2. Press START/STOP
button to run the blender. Blender will run
continuously at the set speed. The LCD will display the motor speed in
percentage. Default speed (percentage) is at 100%. Motor speed can be
changed while blender is running by simply pressing Speed Up
or
Speed Down
button.
3. To stop continuous blending operation, press START/STOP
button
or press any of the program buttons.
PULSE FEATURES
Your unit comes equipped with two PULSE options: Normal Pulse
and
Maximum Pulse
.
Note:
The Pulse buttons are momentary switches — once
released, the unit will shut off.
1. To use Max Pulse option, press the
button. This will run the motor
at 150% speed. The LCD will read “MAX PULSE SPEED: 150%.”
2. To use Normal Pulse option, press the
button. This will run the motor
at 100% speed. The LCD will read “NORM PULSE SPEED: 100%.”
3. The blender allows you to set the pulse to your desired speed. While
blending at Normal Pulse speed, the motor can be adjusted. To do this,
hold the Normal Pulse
button and press Speed Up
or Speed Down
button to adjust the blending speed. The LCD will show the setting
speed, and motor speed will change.
NOTE:
The speed can be set from 5% to 100%. Once the
Pulse
button is released, the motor will shut off and the blender will return to
STANDBY mode. The changed pulse speed will be stored in memory to
replace the default speed of 100%.
REPROGRAMMABLE STATIONS
1. There are 4 Program buttons for four reprogrammable beverage stations
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
70% speed, 10 seconds blend time
70% speed, 15 seconds blend time
70% speed, 20 seconds blend time
70% speed, 25 seconds blend time
2. To run any of the above preset programs, blender must be in
STANDBY mode.
3. Press desired Program button to start the blender. The motor will run at
the preset speed within the preset blending time. The LCD will show time
remaining. Once the blender counts down to 0, the motor will stop running
and the blender will return to STANDBY mode and prompt “PRESS ANY
BUTTON TO BLEND” to begin another function.
NOTE:
To terminate a blending program, simply press START/STOP
button or any of the Program buttons. After doing this, the blender will
return to STANDBY mode and LCD will prompt “PRESS ANY BUTTON
TO BLEND.”
REPROGRAMMING BEVERAGE STATIONS
Users can add 4 new programs to meet their needs. A program can consist
of several sections, each with a different speed and running time.
For example,
can be replaced with a new program that has 3 sections,
as shown below:
Section 1: speed = 75%; time = 30 seconds
Section 2: speed = 100%; time = 20 seconds
Section 3: speed = 50%; time = 20 seconds
The program has the following limitations:
Speed: 5% to 100%
Time: 5 to 90 seconds
Total running time in a program cannot exceed 90 seconds, i.e., sum
of the sections cannot be longer than 90 seconds.
