7
2024730_d•en•2020-01-01
We reserve the right to make technical modifications
Button/
display
Action/result
Press the info button repeatedly until the
desired control function lights up.
e.g.
The LED below the control symbol shows
the state of the control function.
GREEN: Active
RED:
Inactive
e.g.
...
The parameter value of the current control
function is displayed in the upper row of
LEDs (here, limit value 2 of the previously
selected sun control).
RED:
Value 0; the control function is
off
GREEN: Values 1 to 9
FLASHES: Multiple receivers with differ-
ent limit values in the channel.
The value of the first receiver is
displayed.
You can now change this parameter value or switch to
the next info mode using the
button:
Use the arrow keys (
+
light up) to
change the parameter value.
e.g.
...
The upper row of LEDs shows how the
value changes (new value = 1)
Press the button
The transmission LED
lights up for 2
seconds
GREEN: The parameter value was saved
in all receivers of the channel
RED:
Not all receivers could be
reached; press the
button
again.
Leave the info mode using the info button
(
is no longer lit).
OTICE
N
Move commands cannot be sent while the info
mode is active (
lights up).
In the info mode, the WMS hand-held transmit-
ter comfort switches off one minute after the
last press of a button.
If multiple receivers belong to a single channel,
the set parameter value is written to all receiv-
ers of that channel.
Display of the limit values using the WMS hand-
held transmitter comfort
The following table shows the limit values that the display
values of the LED lines on the WMS hand-held transmitter
comfort represent.
Display of the limit values set in the receiver:
The WMS hand-held transmitter comfort converts the
limit values read out of the receiver to values that can be
displayed on the 10 LEDs in the upper row of LEDs. The
displayed limit values therefore only approximate the limit
values from the receiver.
Display of the limit values read out of the receiver
Step
Photo
(klx)
Dawn/dusk
(lx)
Wind
(m/s)
0
OFF
OFF
OFF
1
3...12.5
2...22
0.0...5.5
2
13...17.5
24...36
6.0...6.5
3
18...22.5
38...52
7.0...7.5
4
23...27.5
54...70
8.0...8.5
5
28...32.5
72...90
9.0...9.5
6
33...37.5
92...126
10.0...10.5
7
38...42.5
128...174
11.0...11.5
8
43...47.5
176...300
12.0...12.5
9
48...100
302...500
13.0...25.0
If the first LED (level 0) lights up for the wind limit value,
the wind monitoring is switched off.
If 5 LEDS (level 4) light up, the limit value set in the re-
ceiver is between 8.0 and 8.5 m/s.
Display of the limit values when making settings using
the arrow buttons:
When you change the limit values using the arrow buttons,
the display shown in the upper LED row corresponds to
the values in the following table. These values are written
into the receivers when the data is saved.
Display while limit values are being set
Step
Photo
(klx)
Dawn/dusk
(lx)
Wind
(m/s)
0
OFF
OFF
OFF
1
10
16
5
2
15
30
6
3
20
46
7
4
25
60
8
5
30
80
9
6
35
100
10
7
40
150
11
8
45
200
12
9
50
400
13
If the first LED (level 0) lights up for the photo limit value,
the sun control is switched off.
If you change the value until 7 LEDs light up (level 6), a
limit value of 35 klx is saved in the receivers of the se-
lected channel when the
button is pressed.
