890463_k•en•2019-10-01
We reserve the right to carry out improvements
6
Changing the limit values
CAUTIO
C
Changing these settings may impair
the safety of the system or reduce its
effectiveness. It is better to consult an expert
if you are not sure about the effect of a
change.
Set the limit values as required for your system (to
the product most sensitive to the wind) based on the
following table.
Wind speed limit
Photo limit
"Wind"
switch
position
Wind speed
limit (m/s)
"Brightness"
switch
position
Brightness
limit value
(klx)
TEST
Test
OFF
Off
1
2
1
5
2
3.5
2
15
3
6
3
20
4*
7.5*
4
25
5
9
5
30
6
10.5
6
35
7
12
7
40
8
13.5
8
45
9
15
9
50
10
16.5
10*
55*
11
18
11
60
12
19.5
12
65
13
21
13
70
14
22.5
14
80
15
25
15
>90
*= Factory setting
Iperation
Switching the sun control on/off temporarily
("C" button)
To temporarily switch off the sun control for a channel into
which the weather station has been learned in using the
C
button:
Press the
C
button and hold until the sun shading
system stops moving. Release the button again.
The sun control is now switched off for 12 hours.
After this period, the sun control is reactivated again
automatically.
To reactivate the sun control with the
C
button:
Press and hold the
C
button. Release the button again
when the sun shading system waves.
The sun control is active again.
IUTCCE
O
The sun control can be switched off temporarily
with the master channel or with the auxiliary
channels.
Switching the sun control on/off permanently
Set the switch for the sun control on the weather
station to OFF.
The weather station stops sending brightness-related
move commands.
Set the switch for the sun control on the weather
station to the previous value to switch the sun control
back on.
Cleaning
Photo sensors or solar panels must always be clean
to avoid incorrect measuring values and to ensure
operating reliability. The device should occasionally be
checked for soiling (e.g. bird droppings) and cleaned
carefully. Standard household cleaners may be used.
Do not use solvents.
In snowfall, check daily that the solar panel and
photodiodes are free of snow. A snow-covered weather
station may fail to function properly. If the energy in the
buffer is depleted, the weather station fails completely.
It resumes normal operation after it is recharged via
the solar panel.
The weather station may ice over and the wind wheel
may freeze up in extreme weather conditions. To avoid
wind damage, take your sun shading system out of
operation until wind monitoring can be resumed.
Never remove firmly attached layers of ice and snow.
Scratching, heat and chemical antifreeze agents may
damage the weather station.
Maintenance
There are no parts within the device that require
maintenance.
Strong vibrations at the installation location (for example,
from frequent high wind loads) can loosen the fixing
screws. If the joint screw is not properly tightened, the
orientation of the weather station may change as well.
Therefore, check from time to time that the weather
station is still firmly installed and that all screws are
sufficiently tight.
Liability
Failure to comply with the product information in these
instructions and use of the device in a manner that
contravenes its intended use and purpose may result in
the manufacture refusing to honour warranty claims for
product damage. In this case, liability for consequential
harm to persons or damage to property will also be
excluded. Follow also the instructions in the operating
manual of your sun shading system. The automatic or
manual operation of the sun shading system when iced
over as well as using the sun shading system during
severe weather may cause damages and must be
prevented by the user by taking suitable precautions.
IUTCCE
O
The device meets the requirements on
interference resistance and interference
emission for use in residential and commercial
areas.
Disposal
After its use, the device must be disposed off according to
legal regulations or returned to your local recycling centre!
Heartbeat function
