Wanner Engineering Hydra-Cell G-25-SD Скачать руководство пользователя | Manualshive

Страница: 9 / 20

background image

9

H5-991-406A

H/G-25-SD Service (Fluid End)

Tools and Supplies

The.following.tools.and.supplies.are.recommended.for.servicing.

the.fluid.end.of.the.pump:
•.. Wanner.H/G-5.Tool.Kit.
•.. 1/-in..drive.socket.wrench
•.. 8-mm.and.10-mm.hex-bit.sockets
•.. 16-mm.box-end.wrench
•.. Straightedge.(at.least.10.in..long)
•.. Two.-in..high.blocks,.approximately..to.3.in..wide.and.6.to.

8.in..long

•. 5.mm.hex.Allen.wrench
•.. Medium.Phillips-head.screwdriver
•.. Mallet
•.. Small.torque.wrench.—.rated.to.at.least.7.in.-lbs.(3.N-m)
•.. Torque.wrench.—.rated.to.at.least.50.ft-lbs.(68.N-m)
•.. New.oil
•.. Grease.or.petroleum.jelly
•.. Water.or.compatible.solvent.for.cleaning

The numbers in parentheses are the Reference

Numbers on the exploded view illustrations found

in this manual and also in the Parts Manual.

This.section.explains.how.to.disassemble.and.inspect.all.

easily-serviceable.parts.of.the.pump..Repair.procedures.

for. the. hydraulic. end. (oil. reservoir). of. the. pump. are.

included.in.a.later.section.of.the.manual.

Caution: Do not disassemble the hydraulic end

unless you are a skilled mechanic. For assistance,

contact Wanner Engineering (Tel 612-332-5681 or

Fax 612-332-6937) or the distributor in your area.
Caution: The four capscrews (26) that screw through

the back of the housing into the cylinder casting

hold the casting over the hydraulic end of the pump.

Do not remove them except when repairing the

hydraulic end.

«
...
7
8
9
10
11
...
»

Содержание Hydra-Cell G-25-SD





















Отзывы:

Нет отзывов

Похожие инструкции для Hydra-Cell G-25-SD

Бренд: Watson-Marlow Страницы: 55

Бренд: YANGTECH Страницы: 16

Бренд: DAB Страницы: 40

Бренд: A.O. Smith Страницы: 44

Бренд: PAPILLON Страницы: 16

Бренд: OEM Страницы: 16

Бренд: DAYLIFF Страницы: 12

Бренд: AMICOCIRC Страницы: 13

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Бренд: Wilo Страницы: 19

Бренд: Navien Страницы: 60

FLOJET R4320143A

Бренд: Xylem Страницы: 38

Бренд: FLORABEST Страницы: 94

EzFit EZ 100-76

Бренд: BOCK Страницы: 11

Бренд: Wahl Bach Страницы: 28

Бренд: Immergas Страницы: 16

Бренд: PONNDORF Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды