Wanner Engineering Hydra-Cell G-25-SD Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

15

H5-991-406A

Tools and Supplies

The. following. supplies. are. recommended. for. servicing. the.

hydraulic.end.of.the.pump:
•.. 17.mm.hex.socket.or.box-end.wrench
•.. 3/4.in..(19.mm).open-end.or.adjustable.wrench
•.. 1.in.(6.mm).open-end.or.adjustable.wrench
•.. Emery.cloth.or.ScotchBrite™.pad
•.. Grease
•.. Anaerobic.seal.sealant

The numbers in parentheses are the Reference Numbers

on the exploded view illustrations found in this manual and

also in the Parts Manual.
Caution: Do not disassemble the hydraulic end unless you

are a skilled mechanic. For assistance, contact Wanner

Engineering (Tel 612-332-5681 or Fax 612-332-6937) or the

distributor in your area.
Caution: The four capscrews (26) that screw through the

back of the housing into the cylinder casting (25) hold the

casting to the pump housing. Do not remove them except

when repairing the hydraulic end.
Note: The following service procedures refer several times

to the Wanner Tool Kit. Do not try to repair the hydraulic

end of the pump without using the tools in this kit (available

from Wanner or your local distributor).

H/G-25-SD Service (Hydraulic End)

W0197A

«
...
13
14
15
16
17
...
»

Содержание Hydra-Cell G-25-SD





















Отзывы:

Нет отзывов

Похожие инструкции для Hydra-Cell G-25-SD

Бренд: Gardena Страницы: 13

Бренд: WarmFlow Страницы: 89

Бренд: SAER Elettropompe Страницы: 36

Бренд: Waterous Страницы: 10

Бренд: Watts Страницы: 22

Бренд: Graco Страницы: 32

Smartmax Series

Бренд: ubbink Страницы: 29

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

GPVX 75L Series

Бренд: A.O. Smith Страницы: 52

Бренд: Garland Страницы: 100

Бренд: Slant/Fin Страницы: 16

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

Бренд: Waterax Страницы: 5

Бренд: KAMMAK Страницы: 8

Бренд: Airetool Страницы: 20

Pro VSPHP270JEP

Бренд: Jandy Страницы: 20

ARO 66605J- Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Raypak Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды