background image

Wanhao I3 unboxing and hardware set up. Rev.D                                                                                           

1

 / 

10

 

Unboxing and Hardware Setup   

We packaged your Duplicator i3 very carefully at the Wanhao Bot cave -- we hope you’ll read this   

guide  and  be  just  as  careful  unpacking  it.  In  fact,  you  should  always  be  really  careful  with  The 

Duplicator i3. Here are a few things to keep in mind. 

 

Safety In Safety Information formation 

1.1 Caution:  The  Duplicator  i3  generates  high  temperatures  and  includes  moving  parts  that  can 

cause injury. Never reach inside The Duplicator i3 while it is in operation, and allow time for The 

Duplicator i3 to cool down after operation. 

 

 

 

The Duplicator i3 is sensitive to electrostatic discharge. Make sure you don't have a static charge 

on you by touching a grounded   

 

 

object  before  operating  The  Duplicator  i3  or  attempting  any  adjustments.  If  opening  The 

Duplicator i3 for service, ensure that the power supply is turned off and the cord is disconnected. 

 

 

 

 

Package Contents 

Here are the items that should be found in the Duplicator i3 package:   

-The Duplicator i3   

-Single Step exstruder MK10 

-1x spool holder 

-Hex Wrench and bolt Kit   

- 1 x SD card   

-2 x Wanhao platform tape 

-10 meters PLA filament     

-1 x Power supply cable   

-1 x USB A to B cable   

-1 x filament stand 

Содержание Duplicator i3












Отзывы: