Wanco WI3000P Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

background image

Page | 5

Engine exhaust is very hot. Place the generator at least three feet or one meter away from buildings

or other equipment during operation.

The muffler becomes very hot during operation and remains hot for several minutes after stopping

the engine. Be careful not to touch the muffler while it is hot.

Let the engine cool before storing the generator indoors.

Always make a pre-operation inspection before you start the engine.

Operate the generator on a level surface to prevent fuel spillage or oil starvation.

Know how to stop the generator quickly and understand operation of all controls.

Never permit anyone to operate the generator without proper instructions. Keep children and pets

away from the generator when it is in operation.

Do not operate the generator in rain or snow and do not operate when wet.

«
...
5
6
7
8
9
...
»

Содержание WI3000P





























Отзывы:

Нет отзывов

Похожие инструкции для WI3000P

Бренд: Marathon Electric Страницы: 73

Бренд: Goodmans Страницы: 2

Бренд: Champion Power Equipment Страницы: 38

Бренд: Champion Страницы: 34

Бренд: Xoro Страницы: 122

Бренд: BRUEL & KJAER Страницы: 24

Бренд: Onan Страницы: 108

Marathon Lima Mac

Бренд: Regal Страницы: 23

Бренд: Emerson Страницы: 19

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 144

Бренд: AudioSource Страницы: 8

Бренд: SONIQ Страницы: 12

Бренд: Philips Страницы: 28

Бренд: Philips Страницы: 87

Бренд: VIETA Страницы: 22

Бренд: Chicago Electric Страницы: 28

Бренд: GoVideo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды