Classic Treble Boost
Classic Treble Boost
Brian’s Blues Stack - Bluesy Drive CH2,
Brian’s Blues Stack - Bluesy Drive CH2,
Distortion CH1, stack for lead
Distortion CH1, stack for lead
Factory Reset
Hold down both footswitches during power up to perform a factory reset. This will:
1. Set the default MIDI channel to omni mode.
2. Set all presets to default (ch1 and ch2 off).
Brian’s suggested settings for you to try out:
MIDI
The Pantheon Deluxe can receive CC messages to turn on/off the drive channels and cycle through
presets, and can receive PC messages to load saved presets (limited to the on/off state of the drive
channels). Note: all channel numbers are specified in the range of 1 – 16, and all controller numbers,
controller values, and program numbers are specified in the range 0 – 127.
MIDI Connections
Connect your midi switcher / another pedal by plugging into the
MIDI In
port using either the included
3.5mm to MIDI 5-pin DIN adapter to connect a standard MIDI cable, or if connecting from another pedal
that uses 3.5mm TRS audio connectors, use a standard TRS 3.5mm audio cable. To connect a pedal to
this one further down the chain, connect to the
MIDI Out
port
MIDI Channel
By default the pedal is in omni channel mode and will receive commands on any channel. To set the MIDI
Channel the device will receive commands on:
1. Power off the device, press and hold the Left Footswitch (Channel 2 switch), and power the device on.
2. After power up, releases the switch. Both LEDs will blink.
3. Send a MIDI CC message CC32 with value set to the desired MIDI channel: val=0 is Channel 1, up to
val=15 is Channel 16, val=16 is omni. The LEDs will blink in success.
NOTE: This CC message may be sent on any channel.
MIDI CC messages
The Pantheon Deluxe’s two channels can be turned on and off via MIDI control change messages.
Additionally, the preset number may be incremented or decremented by a specified value.
CC Function
CC no.
Value (0-127)
Description
Channel 1 on/off State
0
0=off, 1-127=on
Sets the on/off state of Channel 1 (Ch1)
Channel 2 on/off State
1
0=off, 1-127=on
Sets the on/off state of Channel 2 (Ch2)
Ch1 off, Ch2 off
2
any value
Sets Ch1 off and Ch2 off when this command is received
Ch1 on, Ch2 off
3
any value
Sets Ch1 on and Ch2 off when this command is received
Ch1 off, Ch2 on
4
any value
Sets Ch1 off and Ch2 on when this command is received
Ch1 on, Ch2 on
5
any value
Sets Ch1 on and Ch2 on when this command is received
Preset Increment
16
0-127
Increments the preset number by <value>
Preset Decrement
17
0-127
Decrements the preset number by <value>
MIDI Channel Assign
32
0-16
0-15 = channel 1-16, 16 = omni mode
MIDI PC messages
The Pantheon Deluxe can be configured to store and recall each channel’s on/off state via MIDI program
changes. To save channel on/off preset:
1. Turn on/off the desired channel(s)
2. Press and hold the Channel 1 footswitch for 2 seconds. Both LEDs will blink slowly to indicate the
Pantheon Deluxe is ready to save the preset
3. Send the desired MIDI program change message (0 to 127). The LEDs will blink quickly in succession
to indicate a successful save.
To load a channel on/off preset:
1. Send a PC message to the Pantheon Deluxe.
PC Function
PC Number
Description
Load a preset
0-127
Loads preset of matching PC number
Save a preset
0-127
When in preset-write mode, sending a PC number will save the current
settings to that preset number
Modern Metal
Modern Metal
Classic Rock
Classic Rock
Distortion Stack - CH1 Classic Distortion,
Distortion Stack - CH1 Classic Distortion,
Engage CH2 for a solo boost
Engage CH2 for a solo boost
Transparent Boost
Transparent Boost