WALMEC TD3 PRO, Инструкция по эксплуатации

Страница: 15 / 68

14
TD
3
PRO TECHNICAL SPECIFICATIONS
Power:
220-240 Vac 50-60 Hz vers. 230 V - 100-130 Vac 50-60 Hz vers.115 V
Maximum power: 3000 W
Insulation:
grounded metallic parts
Power adjustment system: TRIAC driven by electronic controller with built-in PID algorithm based on the thermocou-
ple in the heater
Maximum temperature control system on the resistances: TRIAC driven by thermocouple near the resistances;
safety thermostat
Electrical protections: 16A fuse, 500 mA, 6.3A for vers 230 V - 1A and 8A for vers 115 V
Regeneration duration:
Max 4 h.
Admitted temperature field: from 19° to 70°C - from 66°F to 158°F
Maximum input pressure:
8 bar/116 PSI
Maximum flow: >1200 l/min @ 6 bar - > 42,37 cfm@87 PSI
Air purification:
- first condensation separator stage with 25 micron mesh filter; automatic “heavy duty” condensation drain;
- second coalescent de-greaser stage with 0,01 micron mesh filter; 99,99999% solid particle retention
efficiency; <0.01 mg/m
3
maximum oil residue; manual oily condensate drain;
- absorption dryer third stage with silica gel: <1.2% residual humidity; < -30°C dp - < -22°F dp output air dew point
temperature.
- active carbon fourth stage for gaseous pollutant removal such as oily fumes, hydrocarbons and odours;
<0.003 mg/m
3
maximum oil residue; generates breathable air.
Working pressure regulation:
membrane pressure regulator with pressure gauge downstream from filtering elements.
control and
setting display
on/off
switch
fault
signaller
PID
electronic
control panel
pressure
gauge
pressure
gauge
silica filter saturation
level indicators
water
filter
oil
filter
breathable air outlet
heater
element
active carbon filter
pressure
regulator
solenoid valve SRS
TD
3
PRO
control and
setting display
on/off
switch
fault
signaller
PID
electronic
control panel
pressure
gauge
heater
element
TD
1
PRO
15
PROPER USE
Walcom
®
TD
3
PRO
-TD
1
PRO
is a professional system complete with air treatment for painting.
It is made up of:
- a 25 micron filtering element with condensation centrifuge separator and automatic condensation drain (only TD
3
PRO
)
- coalescent de-greaser filter with 0.01 micron mesh and manual oil drain (only TD
3
PRO
)
- silica gel drying element (only TD
3
PRO
)
- active carbon filtering element (only TD
3
PRO
)
- heating element (TD
3
PRO
-TD
1
PRO
).
This system is designed to:
- treat normal mains compressed air to obtain the most suitable characteristics for painting,
- be installed, except for input and output compressed air hoses, out of explosive environments which in this
case include the spraybooths,
- be installed according to the instructions contained in this manual.
IMPROPER USE
Equipment use other than that described in the previous paragraph may lead to serious health hazards.
Specifically, the following may cause hazardous situations:
- the use of fluids other than normal compressed air,
- installation in explosive environments,
- installation according to criteria other than those indicated in this manual.
TD
1
PRO TECHNICAL SPECIFICATIONS
Power:
220-240 Vac 50-60 Hz vers. 230 V - 100-130 Vac 50-60 Hz vers.115 V
Maximum power: 3000 W
Insulation:
grounded metallic parts
Power adjustment system: TRIAC driven by electronic controller with built-in PID algorithm based on the thermocou-
ple in the heater
Maximum temperature control system on the resistances: TRIAC driven by thermocouple near the resistances;
safety thermostat
Electrical protections: 16A fuse, 500 mA, 6.3A for vers 230 V - 1A and 8A for vers 115 V
Admitted temperature field:
from 19° to 70°C - from 66°F to 158°F
Maximum input pressure: 8 bar/116 PSI
Maximum flow:
>1200 l/min @ 6 bar - > 42,37 cfm@87 PSI
proper use improper use