Wallenstein WXR545PL Скачать руководство пользователя страница 32

Страница: 32 / 42

Service and Maintenance

WXR545PL

Trailer Wood Splitter

9. Service and Maintenance

WARNING!

Risk of serious personal injury. Stop engine

before performing ANY service or maintenance

procedure. Reinstall all covers and guards

removed before putting machine back into

service.

W033

IMPORTANT! Review Maintenance Safety on

page 14

before servicing or repairing. Place the

machine in a Safe Condition before performing

any maintenance. See

page 10

Allow the engine to cool. Engine components and

oil may be hot enough to cause injury.

IMPORTANT! Refer to the engine manufacturer's

manual for engine maintenance and service

information.

9.1 Fluids and Lubricants

1. Engine Oil

SAE 10W-30 or 5W-30 motor oil is recommended

for general use. Refer to the engine manufacturer's

manual for maintenance and service information

2. Grease

Use an SAE multi-purpose high temperature

grease with extreme pressure (EP) performance.

Also acceptable is an SAE multipurpose lithium-

based grease.

3. Engine Fuel

This engine is certified to operate on unleaded

gasoline with a pump octane rating of 86 or higher

(a research octane rating of 91 or higher).

4. Hydraulic Oil

Use Dexron® III Automatic Transmission Fluid

(ATF). Dexron VI or Mercon® ATF are also

acceptable substitutions.

5. Storing Lubricants

Your machine can operate at top efficiency

only if clean lubricants are used. Use clean

containers to handle all lubricants. Store them in

an area protected from dust, moisture and other

contaminants.

9.2 Maintenance Schedule

Perform maintenance procedures at time shown or hour

interval, whichever comes first.

As Required

Check the condition of all hydraulic lines, hoses and

fittings. Replace any that are damaged.
Remove any entangled material from splitter.

Check that all fasteners are tight.

Every 8 hours or Daily

Check fuel level

See

page 25

Check engine oil level.

See

page 24

Every 50 hours or Annually

Check hydraulic oil level.

See

page 24

Clean engine air filter

See

page 25

Inspect hydraulic oil quality

See

page 24

Grease frame slide, hinges,

pivot points

See

page 33

Every 100 hours or Annually

Grease axle bearings

See

page 33

Change engine oil

See engine manual

Check tire pressure

See rating on tire

sidewall

Change hydraulic oil and filter

See

page 34

Change engine air filter

See

page 25

Clean machine. Remove debris

and entangled material.

—

Change fuel filter

See engine manual

Содержание WXR545PL











































Результаты поиска

Содержание WXR545PL

Отзывы:

Похожие инструкции для WXR545PL

Бренды по названию

Популярные бренды

Wallenstein WXR545PL, Руководство оператора

Результаты поиска

Содержание WXR545PL

Отзывы:

Похожие инструкции для WXR545PL

Бренды по названию

Популярные бренды