manualshive.com logo in svg

Wallenstein WX900 Series, Руководство оператора

Поделиться
Скачать
Wallenstein WX900 Series Скачать руководство пользователя страница 29

WX900 Series
Log Splitter

Operating Instructions

29

6.13 Split Wood

 WARNING!

Hands can be pinched, cut, crushed, or severed. 

If two or more people load or operate the 

machine together, a person can be seriously 

injured.
Only one person must load and operate the 

machine.

W036

IMPORTANT!  Do not hold the splitter-control lever to extend 
or retract the cylinder once it has reached the end of its 
stroke. Doing so can overheat the hydraulic fluid and could 
damage the engine.

1. 

Put a log on the splitter, or use the log lifter shelf. 
For instructions, see 

Log Lifter Shelf on page 28.

2. 

Move control lever to the 

Extend 

position until push block 

or wedge starts to split the wood.

3. 

Release the lever when the log splits or cylinder reaches full 
stroke and stops.

4. 

Pull the lever to the 

Retract

 position to retract the push 

block or splitting wedge. The detent holds the lever until the 
cylinder fully retracts, allowing hands-free operation. 

5. 

If the log is large enough to require another split, reposition 
and repeat steps 1-5.

6. 

Pile the split wood close to the working area, but do not 
allow pieces to pile up and clutter the area. A cluttered 
working area can lead to tripping and an accident. 

00644

1

2

3

Figure  20 – 

Splitter-control valve

1.  Extend
2.  Stop
3.  Retract

00646

Figure  21 – 

Split wood

Содержание WX900 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды