background image

9

BA201

Digging with the Backhoe

• 

Swing the dipper out and adjust bucket so the teeth can dig 
into the ground at a slight angle. Lower the boom down to 
set teeth into the ground. Keep the heel of the bucket up 
higher than the teeth.

• 

Retract the dipper to pull the bucket through the soil as it 
fills. Slowly close the bucket at the same time. If necessary, 
apply a downward pressure on the boom to increase 
digging force. 

00108

Fig.  10 – 

Digging with the Dipper Boom

• 

Curl the bucket up when full. Raise the boom and at the 
same time, move the dipper out a little to keep soil from 
building up under the machine. 

00109

Fig.  11 – 

Digging with Bucket

• 

Swing away from your excavation and dump the bucket. 
Start dumping as the bucket approaches the pile. Do not 
waste time by dumping too far from the excavation. Swing 
back to start the next dig.

• 

Deepen the dig with each pass.

IMPORTANT!  Do not use the side of the excavation to stop 
the bucket. The backhoe could be damaged.

 CAUTION!

Operation Hazard! Under certain conditions it 

is possible to contact the stabilizers with the 

bucket. 
Always be aware of the location of the bucket. 

Maintain the 3 ft (1 m) safety zone around the 

stabilizers.

W069

Содержание BA201
















Отзывы: