background image

WX520, WX520L, WX520T
Trailer Wood Splitter

 Safety

Safety

11

• 

Before applying pressure to the system, 
make sure all components are tight, and 
that lines, hoses and couplings are not 
damaged.

• 

Do not attempt any makeshift repairs to the hydraulic lines, 
fittings or hoses by using tapes, clamps or cements. The 
hydraulic system operates under extremely high pressure. 
Such repairs can fail suddenly and create a hazardous and 
unsafe condition.

• 

Wear proper hand and eye protection 
when searching for a high-pressure 
hydraulic leak. Use a piece of wood 
or cardboard as a backstop instead of 
hands to isolate and identify a leak.

• 

If injured by a concentrated high-pressure stream of 
hydraulic fluid, seek medical attention immediately. Serious 
infection or toxic reaction can develop from hydraulic fluid 
piercing the skin surface.

• 

Relieve pressure in the hydraulic system before working on 
it.

2.10 Gas Engine Safety

 CAUTION!

Before starting engine, review the operating and 

maintenance instructions in the engine manual.

W019

•  DO NOT

 operate engine in an enclosed area. Exhaust gases 

contain odorless and deadly carbon monoxide that can 
cause death by asphyxiation.

•  DO NOT

 place hands or feet near moving or rotating parts.

•  DO NOT

 store, spill, or use gasoline near an open flame, 

or devices such as a stove, furnace, or water heater which 
use a pilot light or devices which can create a spark.

•  DO NOT

 refuel indoors where area is not well ventilated. 

•  DO NOT

 refuel while engine is running. Allow engine to cool 

for five minutes before refueling. Store fuel in approved 
safety containers.

•  DO NOT

 remove fuel tank cap while engine is running.

•  DO NOT

 operate engine if gasoline is spilled. Move machine 

away from the spill and avoid engine ignition until gasoline 
has evaporated.

•  DO NOT

 smoke while filling fuel tank.

•  DO NOT

 choke carburetor to stop engine. Whenever 

possible, gradually reduce engine speed before stopping.

•  DO NOT

 run engine above rated speeds. This may result in 

injury.

•  DO NOT

 tamper with governor springs, governor links or 

other parts which may increase the governed speed.

•  DO NOT

 tamper with the engine as set by the original 

equipment manufacturer.

•  DO NOT

 check for spark with spark plug or spark plug wire 

removed.

•  DO NOT

 crank engine with spark plug removed. If engine is 

flooded, crank until engine starts.

•  DO NOT

 strike flywheel with a hard object or metal tool as 

this may cause flywheel to shatter in operation. Use proper 
tools to service engine.

•  DO NOT

 operate engine without a muffler. Inspect 

periodically and replace, if necessary. 

•  DO NOT

 operate engine with an accumulation of grass, 

leaves, dirt or other combustible materials in the muffler 
area.

•  DO NOT

 use this engine on any forest covered, brush 

covered, or grass covered unimproved land unless a spark 
arrester is installed on the muffler. The arrester must be 
maintained in effective working order by the operator. In the 
state of California, the above is required by law (Section 
4442 of the California Public Resources Code). Other states 
may have similar laws. Federal laws apply on federal land.

•  DO NOT

 touch hot muffler, engine body or cooling fins. 

Contact may cause burns.

•  DO NOT

 run engine with air cleaner or air cleaner cover 

removed.

Be sure to:

• 

Remove the wire from the spark plug when servicing 
the engine or equipment to prevent accidental starting. 
Disconnect the (-) ground  wire from the battery terminal. 

• 

Keep engine cooling fins and governor parts free of grass 
and other debris that can affect engine speed.

• 

Examine muffler periodically to be sure it is functioning 
effectively. A worn or leaking muffler should be repaired or 
replaced as necessary.

• 

Use fresh gasoline. Old fuel can clog carburetor and cause 
leakage. 

• 

Check fuel lines and fittings frequently for cracks or leaks. 
Replace if necessary.

Содержание 250754











































Отзывы: