WalkLAB HP9000 Скачать руководство пользователя страница 10

4.2

 

Calibration without Temperature Probe

 

4.2.1  Remove  the  temperature  probe  connected  to  the 

instrument. The temperature display will show a default 
reading of 25.0°C. 

4.2.2

 

Set  the  instrument  to  display  the  temperature  of  the 
buffer  7.00  by  pressing  the  TEMP  SET  key  once.  The 
temperature  digit  will  flash  momentarily.  Press  the  key 
again, the next digit will flash.  Select the digit you wish 
to change while it flashes and press the DIGIT ADV key 
to advance the digit.  Digit will advance at each press 
of the key. Digit will not advance by double pressing. 

4.2.3

 

After setting the temperature, rinse the pH electrode in 
distilled  water.    Dip  the  pH  electrode  into  the  pH  7.00 
rinsing  solution  and  then  into  the  pH  7.00  calibration 
solution and press the CAL key. The OFFSET indicator will 
flash  momentarily.  Once  the  instrument  detected  the 
correct  offset  buffer,  the  OFFSET  indicator  will  stop 
flashing and offset value will be displayed. 

4.2.4

 

Now  the  instrument  is  performing  a  multiple  data 
sampling.  It will take a little longer time for an accurate 
calibration point.  

4.2.5  When  OFFSET  point  is  established,  the  instrument  will 

beep and the SLOPE indicator will flash. 

4.2.6

 

Repeat  step  4.2.2  to  set  the  temperature  of  the  slope 
buffer if required.  

4.2.7

 

Rinse  the  pH  electrode  in  distilled  water  and  then  pH 
4.01 or 10.01 rinsing solution. Dip the pH electrode in pH 
4.01 or 10.01 calibration solution. 

4.2.8

 

The  SLOPE  indicator  will  stop  flashing  when  the 
instrument  detects  the  correct  slope  buffer  and  will 
display the buffer reading. 

Содержание HP9000

















Отзывы: