Waldorf FNB8120GE Скачать руководство пользователя страница 13

Страница: 13 / 39

Installation

A suitable joining compound which resists the breakdown action of LPG must be used on every gas

line connection, unless compression fittings are used.

Connection to appliance is

” BSP male.

NOTE: A Manual Isolation Valve must be fitted to individual appliance supply line.

Correctly locate appliance into its final operating position and using a spirit level, adjust legs so that

unit is level and at correct height.

Connect gas supply to appliance.

Check all gas connections for leakages using soapy water or other gas detecting equipment.

Check gas supply pressure is as shown in Specifications section, Gas Supply Requirements

table.

NOTE: Measure gas supply pressure at Upper Test Point (Supply Pressure) on the gas control

valve.

Light Pilot Burners. Refer to Operation section, Lighting Pilot Burners.

Check pilot flame size. Re-adjust if required, using pilot adjusting screw (See Fig 3 below), and as

shown in Gas Conversion and Specifications section, Pilot Burner Flame Adjustment.

Light the Main Burners. Refer to Operation section, Lighting Main Burners.

10. Verify Supply Pressure is still correct.
11. Check Main Burner operating pressure (Adjust, using

Operating Pressure Adjusting Screw on Gas Control

Valve, see Fig 3), and as shown in Gas Conversion

and Specifications section, Main Burner Operating
Pressure Adjustment.

NOTE: Insufficient gas supply line capacity, indicated by

operating pressure drop during maximum gas
supply demand, is NOT ACCEPTABLE and may
invalidate the manufacturers warranty for this
appliance.

Ensure the tank(s) is / are filled with either water or oil prior to starting Main
Burners otherwise the fryer tank(s) may be damaged.

Caution

IMPORTANT:

Control Panel ‘ON / OFF’ Key provides ‘ON / OFF’ control of Controller and Main Burner
heating cycles ONLY.

Gas Valve Control Knob is used to turn the Gas System ‘ON / OFF’ as well as providing Pilot
Ignition and Pilot Standby functions.

NOT

USE

NAKED

FLAME

CHECK

FOR

GAS

LEAKAGES

Warning

Supply Pressure

Test Point

Operating Pressure

Test Point

Pilot Adjusting

Screw

Operating Pressure

Adjusting Screw

Fig 3

Содержание FNB8120GE








































Результаты поиска

Содержание FNB8120GE

Отзывы:

Бренды по названию

Популярные бренды

Waldorf FNB8120GE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FNB8120GE

Отзывы:

Бренды по названию

Популярные бренды