289.805.003
25
Date: 2018-11-28
Mini Roll Down – Cheat Sheet
MODE
Function
DMX
channel
Function
1
Positioning with slow ramp
1
Position rough (Hi of a 16 bit DMX channel)
2
Positioning with medium ramp
2
Position fine (Lo of a 16 bit DMX channel)
3
Positioning with fast ramp
3
Set the maximum speed
4
Positioning with slow ramp hard-limits active
4
60-65%
Save setting
Enabled
5
Positioning with medium ramp hard-limits active
Else
S
ave setting
Disabled
6
Positioning with fast ramp hard-limits active
5
Set soft-limit
TOP
position, moving up
7
Set soft top and bottom limits using the control box
6
Set soft-limit
BOTTOM
position, moving down
8
Run to top or bottom position using the control box
9
Manual up (DMX address = speed)
0
Manual down (DMX address = speed)
WARNING!
Do not use the product
if any damage is found!
How to get started
1.
Put on fabric/curtain on the tube.
2.
Apply DMX from a Lighting desk, ideally a desk with manual faders.
3.
Make sure that your six channels are patched from DMX channel 1 to 6.
4.
Pull all channels on to 0%
5.
Apply power to the Mini Roll Down and set the address to 0 0 1 and the mode to 1 -
DMX lamp should be lit.
6.
Set DMX channel 4 to 63% -
This enables the saving of soft-limit top and bottom position.
7.
Pull channel 5 to 20 % -- the Mini Roll Down starts moving up.
8.
Stop the Mini Roll Down (pull channel 5 to 0%) when the desired top position is reached.
9.
Pull channel 6 to 20 % -- the Mini Roll Down starts moving down.
10.
Stop the Mini Roll Down (pull channel 6 to 0%) when the desired bottom position is reached.
11.
Pull channel 1 (position) to 75 %
12.
Pull channel 3 (speed) to 50% -
The Mini Roll Down starts to move up, with 50% speed, to a position that is 75% up.
13.
Pull channel 1 (position) to 25% -
T
he Mini Roll Down starts to move down, with 50% speed, to a position that is 25% up.
Before each use
−
Inspect the
Mini Roll Down
for damage, wear, corrosion or abuse.
−
Inspect the
fabric/curtain attachment
for damage, wear, corrosion or abuse
and secure the fabric/curtain is safely attached and within maximum weight.
−
Check that the
Mini Roll Down
is securely mounted according to the user
manual.
Green LED indicators:
LED next to the DMX-selectors.
Glows constant:
DMX connection is correct.
Flashing:
DMX signal is missing.
LED next to the DMX-selectors.
Fast flashing:
The roll down needs to be reset, before it can be used.
Slow flashing:
The roll down’s is moving towards the set position
Steady light:
The set position has been reached and the motor stopped.
Tech specs:
Slow Motor
Lifting speed
Variable 2.5-26 cm/s
(1.0-10.2 in/s)
Maximum load
7.5 kg (16.5 lb)
Fast Motor
Lifting speed
Variable 5-61 cm/s
(2.0-24.0 in/s)
Maximum load
3.0 kg (6.6 lb)
Control box and Hard-limit switch - XLR 4 pole
Pin 1 - GND (COM/switch return)
Pin 2 - Down (CCW) control NO / CW (Up) hard-limit NC
Pin 3 - Up (CW) control NO / CCW (Down) hard-limit NC
Pin 4 - +5VDC output (optional)
