Wahl 8467, Руководство пользователя

Страница: 5 / 7

Adjusting the power screw (Not found in all Wahl models)
If your clipper has a power screw, it has been adjusted for peak efficiency before leaving the factory. However, if the voltage in your home is low, you may need to readjust it. To
adjust power, first use the on/off switch to turn appliance on, then use the plastic brush, a screwdriver or a thin coin to turn power screw(E) in a clockwise direction until the arm
strikes the coil, making a noise (Fig. 3b). Then slowly turn power screw out (counterclockwise) just until noise stops. This is the maximum power setting (Fig. 3a).
Cutting length adjustment
Cutting lengths for different models(not found in all models):
· Raise the adjustment lever – minimum cutting length (Fig. 4a).
· Lower the adjustment lever – maximum cutting length (Fig. 4b).
Cutting with attachment combs (depending on model)
The appliance can also be operated with attachment combs. Attachment combs can be used to extend the cutting length range. Depending on the model, different-sized
attachment combs are included in the scope of supply.
Accessories are available from your dealer.
Attaching/removing the attachment comb
f
Set the adjustment lever to the shortest cutting length (Fig. 4b).
1. Place the attachment comb onto the cutting edge of the blade set and press it down onto the blade set in the direction of the housing until it clicks into position (Fig. 3a).
2. The attachment comb can be easily removed by lifting the hook in the direction of the arrow (Fig. 5b).
Changing the blade set
Warning! Injuries and material damage due to incorrect handling.
f
Switch the appliance off and disconnect from the power supply before changing the blade set.
1. Switch the appliance off using the on/off switch (Fig. 2b) and disconnect from the power supply.
2. Undo the screws on the blade set; remove the bottom blade and the top blade (Fig. 7).
When assembling, the bottom blade and the top blade should be aligned as follows:
f
Set the adjustment lever to the shortest cutting length (Fig. 4a).
3. Place the top blade on the plastic cam (Fig. 8).
4. Position bottom blade and reinsert the two screws.
5. Before tightening the screws, align the bottom blade (Fig. 9).
Warning! Injuries due to incorrect handling.
f Align the bottom blade so that there is a gap of 0.5 mm to 1.0 mm between the front edge of the bottom blade and the front edge of the top blade (Fig. 9)
6. Tighten screws (Fig. 7).
CARE AND CLEANING
Danger! Electric shock due to penetration of liquid.
f
Switch the appliance off and disconnect from the power supply, before you start with cleaning and care.
f
Do not immerse the appliance in water!
f
Do not allow any liquid to get inside the appliance.
f
Only reconnect the appliance to the power supply if it is completely dry.
Handle with care! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and accessories.
f
Never use solvents or scouring agents.
f
Only use cleaning agents and blade set oil recommended by the manufacturer.
Hygienic spray and blade set oil are available from your dealer or our service centre.
f
Remove the attachment comb (Fig. 5b) after every use. Remove the hair clippings from the blade set with the cleaning brush.
f
If a thorough cleaning is required, the blade set can be removed. See chapter Changing the blade set.
f
After cleaning the blade set, we recommend using hygienic spray. It keeps all blade sets hygienically clean and is effective against bacteria and viruses.
f
Oil the blade set with the blade set oil (Fig. 6).
f
We recommend that you clean and care for your blade set during and after clipping. Oiling and cleaning of the blade set protects against corrosion.
f
Switch the appliance on briefly (approx. 10 seconds) to ensure the oil film is evenly distributed.
f
For a good and long-lasting cutting performance, it is important to oil the blade set frequently
f
If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade set should be replaced.
f
Only wipe the appliance with a soft, slightly damp cloth.
Problem elimination
Blade set is cutting badly.
Blade set is pulling hair out.
Cause: Blade set is dirty.
f
Clean and oil the blade set (Fig. 6).
Cause: Blade set is worn out.
f
Replace the blade set (Fig. 7/8/9).
Skin injury
Cause: Too much pressure on the skin.
f
Less pressure on the skin.
Cause: Cutting angle is too high.
f
Hold appliance more flatly to the skin.