Wahl 1871 Li, Руководство по эксплуатации

Страница: 11 / 96

11
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
Disposal
Handle with care! Environmental damage in the event of
incorrect disposal.
f Discharge batteries prior to disposal!
f Correct disposal will ensure environmental protection
and prevent any potentially harmful impact on people
and the environment.
Adhere to the relevant legal requirements when disposing of the
appliance.
Information on the disposal of electrical and electronic appliances
in the European Community:
Within the European Community, national regulations are
specified for the disposal of electrical appliances, based
on EU Waste Electrical and Electronic Equipment Directive
2012/19/EC (WEEE). In accordance with this, the appliance
can no longer be disposed of with the local or domestic
waste.The appliance will be accepted free of charge by local
collection points or recycling centres. The packaging for this
product is made from recyclable materials. Dispose of this in
an environmentally friendly manner by recycling it.
Accessories and spare parts are available from your dealer or
our service centre.
f
Remove the attachment comb (Fig. 6
ⓑ
) after every use and lift
the blade set out of the housing (Fig. 7
ⓐ
). Use the cleaning brush
to remove any cut hairs from the housing opening and from the
blade set (Fig. 8). The cleaning lever can also be pressed. This allows
the cut hairs that accumulate between the bottom blade and the
top blade to be easily removed using the cleaning brush ( EASY
CLEANING ).
f
Only wipe the appliance with a soft, slightly damp cloth.
f
The blade set using the hygienic spray.
f
Oil the blade set with the blade set oil (Fig. 9).
f
For a good and long-lasting cutting performance, it is
important to oil the blade set frequently.
f
If the cutting performance deteriorates after long use
despite regular cleaning and oiling, the blade set should
be replaced.
Automatic Sensor System
To give you advance notice of an urgent need for maintenance care,
your hair cutting appliance has been equipped with an automatic sen-
sor system.
·
The sensor system automatically recognises when the
blade set needs oiling or cleaning. After the appliance is
switched off, an acoustic signal will sound and the bat-
tery power indicator will flash for 2 minutes.
·
The acoustic signal and the flashing of the battery power
indicator can be cancelled (turned off) by briefly switch-
ing the appliance on and off.
·
Before using the appliance again, it is
urgently recom-
mended
to clean the appliance and oil the blade set,
see chapter
Cleaning and care
.
·
Failure to observe these instructions may result in dam-
age to and early failure of the appliance, which will void
all guarantee claims.
Changing the blade set
1. Slide the blade set off the housing in the direction of the arrow (Fig.
7
ⓐ
). Remove the blade set.
2. Replace the blade set by hooking it into the housing and pressing it
down until it clicks into position (Fig. 7
ⓑ
).
Problem elimination
Blade set is cutting badly or pulling hair out
Cause: Blade set is dirty or worn out.
f Clean and oil the blade set (Fig. 8/9); if this does not resolve the
problem, replace the blade set (Fig. 7).
Battery operating time is too short
Carefully clean and oil the blade set (Fig. 8/9). A blade set that is very
dirty and has not been oiled can halve the available battery operating
time! If the blade set is clean and oiled and the battery operating time
is still far too short, it is likely that the batteries are nearing the end of
their life.
Battery operating time generally decreases at a steady rate
when used on a day-to-day basis. The batteries used here are
specially designed for professional and everyday use, but are
also affected by this..
Skin injury
Cause: Too much pressure on the skin.
f Reduce pressure when cutting close to skin.
Cause: Damaged blade set.
f Check whether the blade edges were damaged during use and
replace the blade set if necessary.
Battery power indicator light does not light up
Cause: Appliance has not been correctly placed on the charging stand.
f Ensure that the hand-held appliance has been correctly placed on
the charging stand.
Cause: Defective power supply.
f Ensure that the power supply unit is plugged into the mains socket.
f Check the mains cable for possible damage.
f Check the power supply.
Entire battery power indicator is flashing
f Check whether the blade set is blocked and the blade is able to
move. Switch the appliance on and off. If the entire display is flash-
ing, please contact your specialist retailer or a WAHL service centre.
In the event that this information does not help you resolve your
problem, please contact our service centre. Never attempt to repair the
appliance yourself!