WAGO I/O SYSTEM 750 страница 153 Скачать руководство пользователя | Manualshive

Страница: 153 / 260

background image

WAGO I/O System 750

Diagnostics 153

750-8210/040-000 PFC200; G2; 4ETH; XTR

Manual

Version 1.7.0, valid from FW Version 04.01.10(23)

Table 62: Error Code 3, Explanation of Blink Codes and Procedures for Troubleshooting

Error

Argument

Cause

Solution

--

Local bus communication
error; defective I/O module
cannot be identified

If a power supply module (e.g., 750-602)
is connected to the controller, ensure
that this module functions properly (see
Section

“LED Signaling”). If the supply

module does not exhibit any errors/faults,
the I/O module is defective. Identify the
defective I/O module as follows:

-

Switch off the power supply.

-

Place the end module in the middle
of the I/O modules connected to the
system.

-

Switch the power back on.

-

If the I/O LED continues to flash red
switch off the power supply again
and place the end module in the
middle of the first half of the I/O
modules (toward the controller).

If only one I/O module is left and the LED
continues to flash, either this module or
the controller local bus interface is
defective. Replace the defective module
or the controller.

-

If the LED is no longer flashing,
switch off the power supply and
place the end module in the middle
of the second half of the I/O modules
(away from the controller).

-

Switch the power back on.

-

Repeat this procedure until you
establish which I/O module is
defective. Then replace that module.

«
...
151
152
153
154
155
...
»

Содержание I/O SYSTEM 750





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O SYSTEM 750

MME239 - Micro DVD Home Theater System

Бренд: Magnavox Страницы: 39

Бренд: Peco Services Страницы: 2

Бренд: M-system Страницы: 6

Бренд: M-system Страницы: 4

Бренд: JBL Страницы: 8

Бренд: M-system Страницы: 10

Бренд: Carel Страницы: 2

Бренд: Daewoo Страницы: 21

Бренд: Magnavox Страницы: 24

Бренд: Senju Sprinkler Страницы: 8

Бренд: Locinox Страницы: 63

Бренд: Pattfield Страницы: 94

Autoscript WHC-IP A9009-0005

Бренд: Vitec Multimedia Страницы: 20

Braukmann HS10S

Бренд: resideo Страницы: 38

Бренд: SCS Страницы: 88

Бренд: Omron Страницы: 154

Бренд: ICP DAS USA Страницы: 2

Бренд: Cattron Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды