WAGO I/O-SYSTEM 750 753-501 Скачать руководство пользователя страница 50

Страница: 50 / 54

Use in Hazardous Environments

WAGO-I/O-SYSTEM 750

753-501 2DO 24V DC 0,5A

Manual

Version 1.2.0

8.2.4

Special Conditions for Safe Use

(IEC-Ex Certificate IECEx TUN 12.0039 X)

For use as Gc- or Dc-apparatus (in zone 2 or 22) the Field bus independent

I/O Modules WAGO-I/O-SYSTEM 750-*** Ex i shall be erected in an

enclosure that fulfils the requirements of the applicable standards (see the

marking) IEC 60079-0, IEC 60079-11, IEC 60079-15, IEC 60079-31.

For use as group I electrical apparatus M2 the apparatus shall be erected in

an enclosure that ensures a sufficient protection according to IEC 60079-0

and IEC 60079-1 and the degree of protection IP64.

The compliance of these requirements and the correct installation into an

enclosure or a control cabinet of the devices shall be certified by an ExCB.

Measures have to be taken outside of the device that the rating voltage is not

being exceeded of more than 40 % because of transient disturbances.

The connecting and disconnecting of the non-intrinsically safe circuits is

only permitted during installation, for maintenance or for repair purposes.

The temporal coincidence of explosion hazardous atmosphere and

installation, maintenance resp. repair purposes shall be excluded.

For the type the following shall be considered: The Interface circuits shall

be limited to overvoltage category I/II/III (non mains/mains circuits) as

defined in IEC 60664-1.

Содержание I/O-SYSTEM 750 753-501























































Результаты поиска

Содержание I/O-SYSTEM 750 753-501

Отзывы:

Похожие инструкции для I/O-SYSTEM 750 753-501

Бренды по названию

Популярные бренды

WAGO I/O-SYSTEM 750 753-501, Руководство пользователя

Результаты поиска

Содержание I/O-SYSTEM 750 753-501

Отзывы:

Похожие инструкции для I/O-SYSTEM 750 753-501

Бренды по названию

Популярные бренды