WAGO 750-486/040-000 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 102

background image

WAGO-I/O-SYSTEM 750 XTR

Connect Devices

49

750-486/040-000 4AI 0/4-20mA NE43 Ex i XTR

Manual

Version 1.0.0

6.2

Power Supply Concept

Ex i XTR I/O modules shall only be supplied via “Power Supply 24 VDC
Diagn for Ex I XTR Modules”

Ex i XTR I/O modules shall only be operated with a “Power Supply 24 VDC
Diagn for Ex I XTR Modules” 750-606/040-000.

Keep the air and creep distances between intrinsically safe segments!

The maximum current available from the 750-606/040-000 “Power Supply
24 VDC Diagn for Ex i XTR Modules” is 1 A.
If the use of further 750-606/040-000 is necessary for reasons of extent of
utilization, 4 Separation Modules (750-616/040-000) must be used to guarantee
the distance between the intrinsically safe segments.

Do not exceed maximum current via power contacts!

The maximum current available from the “Power Supply 24 VDC Diagn for Ex i
XTR Modules” 750-606/040-000 is 1 A. Greater currents can damage the power
contacts. When configuring the system, ensure that this current is not exceeded.
If exceeded, an additional 750-606/040-000 must be used.

Further information about explosion prevention!

Further information about explosion prevention can be found in section “Use in
Hazardous Environments”!

The Ex i XTR I/O module receives the 24 V voltage supply for the field level from
an upstream Ex i XTR I/O module or from the “Power Supply 24 VDC Diagn for
Ex i XTR Modules” 750-606/040-000 via the power contacts used as blade
contacts. It then provides this potential to subsequent I/O modules via the power
contacts used as spring contacts.

«
...
47
48
49
50
51
...
»

Содержание 750-486/040-000







































































































Отзывы:

Нет отзывов

Похожие инструкции для 750-486/040-000

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: Valor Страницы: 20

Бренд: Omegalink Страницы: 2

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: RADEMACHER Страницы: 48

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Бренд: Ros Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды