WAGO 750-344 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 82

WAGO 750-344 Скачать руководство пользователя страница 71

Feldbus Coupler 750-344 / -345

•

71

LED Indication

WAGO-I/O-SYSTEM 750

INTERBUS

3.1.7.3 Node Status

The I/O-LED indicates the operation of the node and signals faults occurring.

I/O

Meaning

green

Data cycle on the internal bus

Off

No data cycle on the internal bus

red

Hardware defect in the coupler

red
flashing

During runup: Internal bus initialized
During operation: General internal bus error

red
flashing cycle

Fault message during internal bus reset and internal fault

orange

I/O LED lights up orange during an update of the bus coupler
firmware. The color orange cannot be indicated during normal
operation.

Coupler boot-up occurs after switching on the power supply. While doing so,
the I/O LED flashes red. In the case of an error the I/O LED continues
blinking red.
In the event of error, the I/O LED continues to flash red. The error is indicated
by the blink code cycle.

Suppl

y

voltage

switch on

Coupler start

“I/O” LED is blinking red

Error

No

Yes

“I/O” LED

is shining green

Fieldbus start

“I/O”LED

1st flash sequence

(Introduction of the error indication)

1st pause

“I/O” LED

2nd flash sequence

Error code (number of flash c

y

cles)

“I/O” LED

3rd flash sequence

Error argument (number of flash c

y

cles)

2nd pause

Fig. 3-11: Signaling the node status

g012118d

«
...
69
70
71
72
73
...
»

Содержание 750-344



















































































Отзывы:

Нет отзывов