Wacker Neuson Trowel CT 24-4A Скачать руководство пользователя страница 24

Страница: 24 / 68

wc_tx003232gb.fm

Operation

CT 24-4A

4.4

Refueling the Machine

Requirements

Machine shut down

Engine cool

Machine/fuel tank level with the ground

Fresh, clean fuel supply

Procedure

Perform the procedure below to refuel the machine.

1. Remove the fuel cap

(a)

2. Fill the fuel tank to the bottom of the fuel tank neck

(b)

3. Reinstall the fuel cap.

Result

The procedure to refuel the machine is now complete.

WARNING

Fire hazard. Fuel and its vapors are extremely flammable. Burning fuel can cause
severe burns.

Keep all sources of ignition away from the machine while refueling.

Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.

Refuel only when the machine is outdoors.

Clean up spilled fuel immediately.

wc_gr008400

wc_gr008401

CAUTION

Fire and health hazard. Fuel expands when heated. Expanding fuel in an over-filled
tank can lead to spills and leaks.

Do not overfill the fuel tank.

Содержание Trowel CT 24-4A





































































Результаты поиска

Содержание Trowel CT 24-4A

Отзывы:

Похожие инструкции для Trowel CT 24-4A

Бренды по названию

Популярные бренды

Wacker Neuson Trowel CT 24-4A, Руководство оператора

Результаты поиска

Содержание Trowel CT 24-4A

Отзывы:

Похожие инструкции для Trowel CT 24-4A

Бренды по названию

Популярные бренды