background image

Safety Information

BFS 614B

wpm_si000338gb.fm

4

1.

Safety Information

This manual contains DANGER, WARNING, CAUTION, 

NOTICE, 

and

NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service. 

This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.

NOTICE

:

 Used without the safety alert symbol, 

NOTICE

 indicates a

situation which, if not avoided, could result in property damage.

Note:

  

Contains additional information important to a procedure.

1.1

Laws Pertaining to Spark Arresters

Notice:

  State Health Safety Codes and Public Resources Codes

specify that in certain locations spark arresters be used on internal
combustion engines that use hydrocarbon fuels.  A spark arrester is a
device designed to prevent accidental discharge of sparks or flames
from the engine exhaust.  Spark arresters are qualified and rated by
the United States Forest Service for this purpose.
In order to comply with local laws regarding spark arresters, consult
the engine distributor or the local Health and Safety Administrator.

DANGER

WARNING

CAUTION

Содержание BFS 614B





































Отзывы: