Wacker Neuson BFS 1318AS Скачать руководство пользователя страница 7

7

Revision 03/05/07

BFS SERIES

 Safety Information

                .1         Operating Safety

 

Familiarity and proper training are required for the safe operation of
equipment! Equipment operated improperly or by untrained personnel
can be dangerous! Read the operating instructions contained in both
this manual and the engine manual and familiarize yourself with the
location and proper use of all controls. Inexperienced operators 
should receive instruction from someone familiar with the equipment 
before being allowed to operate the machine.

NEVER operate this machine in applications for which it is not
intended.  
NEVER allow anyone to operate this equipment without proper
training. People operating this equipment must be familiar with the
risks and hazards associated with it.
NEVER touch the engine or muffler while the engine is on or
immediately after it has been turned off. These areas get hot and 
may cause burns.
NEVER use accessories or attachments that are not recommended 
by Wacker. Damage to equipment and injury to the user may result.
NEVER leave machine running unattended.
NEVER tamper with or disable the function of operating controls.
NEVER use choke to stop engine.
NEVER operate the machine in areas where explosions may occur.

ALWAYS read, understand, and follow procedures in Operator’s
Manual before attempting to operate equipment.
ALWAYS be sure that all other persons are at a safe distance from 
the machine. Stop the machine if people step into the working area 
of the machine.
ALWAYS be sure operator is familiar with proper safety precautions
and operation techniques before using machine.
ALWAYS wear protective clothing appropriate to the job site when
operating equipment.
ALWAYS wear hearing protection when operating equipment.
ALWAYS keep hands, feet, and loose clothing away from moving 
parts of the machine.
ALWAYS use common sense and caution when operating the
machine.
ALWAYS be sure the saw will not tip over, roll, slide, or fall when
not being operated.
ALWAYS turn the engine OFF when the saw is not being operated.

WARNING

2.1.1      

2.1.2  

2.1.3  

2.1.4  

2.1.5  
2.1.6  
2.1.7  
2.1.8  

2.1.9  

2.1.10  

2.1.11  

2.1.12  

2.1.13  
2.1.14  

2.1.15  

2.1.16  

2.1.17  

Содержание BFS 1318AS































Отзывы: