WABCO 1200E Скачать руководство пользователя

Страница: 34 / 52

Troubleshooting and Testing

Meritor WABCO

Maintenance Manual 34 (Revised 03-16)

No air pressure
build-up in system.

Air dryer not plumbed correctly
(connections reversed).

Yes

Ensure compressor discharge line is
plumbed to air dryer port 1, and air
dryer port 21 is connected to vehicle’s
supply tank.

Wrong air line connected to
dryer port 4.

Yes

Ensure dryer port 4 line is connected to
the “UNL” port of the air governor.

Air governor not working
properly.

Yes

Inspect governor per manufacturer’s
instructions. Repair or replace as
needed.

Air system leaks, such as
compressor discharge line, air
dryer, reservoirs, brake or
suspension valves, etc.

Yes

Locate leak(s) and repair.

Air dryer leaks from purge valve.

Yes

Refer to purge valve conditions listed in
this chart.

Pressure protection elements
will not open.

Yes

Replace the air dryer. The pressure
protection elements are
non-serviceable.

Water in tanks; often
following
aftermarket
installation or when
dryer is a
replacement for a
competitive brand.

Pressure-controlled check valve
not installed in correct tank or
not installed at all.

Yes

Install pressure-controlled check valve
in secondary tank.

Pressure-controlled check valve
properly installed, but one-way
check valve not removed.

Yes

Remove one-way check valve so that
only the pressure-controlled check valve
is installed between the secondary tank
and supply tank.

Water, oil, or sludge
in air system tanks.

Desiccant contaminated with oil.

Yes

Replace desiccant. Inspect compressor
per manufacturer’s instructions.

Water in system
tanks.

Dessicant saturated.

Maintenance interval not
followed.

Yes

Replace dessicant cartridge.

Water in system
tanks, everything
else checks out
okay.

Dryer not suitable for
application.

Yes

Review the application guidelines. Refer
to TP-9672. For assistance, call the
Meritor OnTrac™ Customer Call Center
at 866-OnTrac1 (668-7221).

Condition

Possible Cause

Conditions May Occur In:

Solution

Regeneration
Style Air
Dryers

Dedicated
Purge Tank
Air Dryers

Содержание 1200E





















































Результаты поиска

Содержание 1200E

Отзывы:

Похожие инструкции для 1200E

Бренды по названию

Популярные бренды

WABCO 1200E, Руководство по обслуживанию

Результаты поиска

Содержание 1200E

Отзывы:

Похожие инструкции для 1200E

Бренды по названию

Популярные бренды