WABCO 1200E Скачать руководство пользователя

Страница: 33 / 52

Troubleshooting and Testing

Meritor WABCO

Maintenance Manual 34 (Revised 03-16)

Air leak at turbo
cut-off valve vent.
Rubber seal
damaged or missing.

NOTE:

As of Nov.

2009, the turbo
cut-off valve will have
an O-ring instead of a
lip seal.

Temperature of air coming into
dryer is too high — not enough
cooling takes place before dryer
inlet.

Yes

Move dryer farther from compressor.
Add additional compressor discharge
line before air dryer. Add cooling coil or
heat exchanger before air dryer.

NOTE:

Inlet air temperature must not

exceed 175

F (80

C).

Lip seal installed upside-down
on piston. Lip must face UP
(towards dryer).

Yes

Install lip seal correctly.

Valve bore worn excessively.

Yes

Inspect valve bore for wear. If a new
turbo cut-off valve does not seal in a
clean, lubricated bore, replace the air
dryer.

Piston is broken.

Yes

Replace the turbo cut-off valve.

Air dryer frozen
(water collecting in
base of dryer is
freezing).

No electrical power to heater
connector.

Yes

Check for a blown fuse. Repair heater
circuit.

NOTE:

There must be power to the

heater connector the entire time the
vehicle’s ignition is

Low voltage to heater connector.

Yes

Repair cause of low voltage, such as
poor electrical ground, bad connections,
corroded wire splices, etc.

Heater assembly not working.

Yes

Replace heater assembly.

Wrong voltage air dryer used;
i.e., 12-volt air dryer used in a
24-volt system.

Yes

Replace with correct voltage air dryer.

Condition

Possible Cause

Conditions May Occur In:

Solution

Regeneration
Style Air
Dryers

Dedicated
Purge Tank
Air Dryers

Содержание 1200E





















































Результаты поиска

Содержание 1200E

Отзывы:

Похожие инструкции для 1200E

Бренды по названию

Популярные бренды

WABCO 1200E, Руководство по обслуживанию

Результаты поиска

Содержание 1200E

Отзывы:

Похожие инструкции для 1200E

Бренды по названию

Популярные бренды