background image

32

1.  Check the oil level. See the 

How to Check/Add Oil

 section. 

2.  Move the fuel lever (I) to the ON position. 
3.  Move the choke lever (J) to the choke CLOSED position. Note: Choke is usually  

    unnecessary when restarting a warm engine. 
4.  Turn the Engine switch (F) to the ON position. 
5. 

Recoil Start

: Firmly hold the starting handle (H). Pull the starter cord handle slowly  

    until resistance is felt, then pull rapidly.

!

WARNING

Rapid retraction of the starter cord (kickback) 

will pull your hand and arm toward the engine 

faster than you can let go. Broken bones, 

fractures, bruises or sprains could result. When 

starting engine, pull the starter cord slowly until 

resistance is felt and then pull rapidly to avoid 

kickback.

6.  Electric Start: (Optional) Turn the key to the Start position, then hold it there until the  

    engine starts. Note: If engine fails to start within 5 seconds, release the key, and wait  

    at least 10 seconds before operating the starter again.

How to stop the engine

!

WARNING

Petrol and its vapors are extremely flammable 

and explosive. 
Fire or explosion can cause severe burns or 

death.

1.  Turn Engine switch (F) to the OFF position. 
2.  Turn Fuel lever (I) to the OFF position.

Содержание VF3000P













































Отзывы: