background image

This Manual is prepared for the use of trained Vulcan Service
Technicians and should not be used by those not properly qualified.

This manual is not intended to be all encompassing. If you have not
attended a Vulcan Service School for this product, you should read,
in its entirety, the repair procedure you wish to perform to
determine if you have the necessary tools, instruments and skills
required to perform the procedure. Procedures for which you do not
have the necessary tools, instruments and skills should be
performed by a trained Vulcan Service Technician.

The reproduction, transfer, sale or other use of this Manual, without
the express written consent of Vulcan, is prohibited

.

This manual has been provided to you by ITW Food Equipment
Group LLC ("ITW FEG") without charge and remains the property
of ITW FEG, and by accepting this manual you agree that you will
return it to ITW FEG promptly upon its request for such return at
any time in the future.

948RX

SERVICE  MANUAL

HEAVY DUTY GAS GRIDDLES

MODELS

924RX

MSA24

936RX

MSA36

948RX

MSA48

960RX

MSA60

972RX

MSA72

For additional information on Vulcan-Hart Company or to locate an authorized parts
and service provider in your area, visit our website at www.vulcanhart.com.

A product of VULCAN-HART

LOUISVILLE, KY 40201-0696

F25383 (510)

Содержание 924RX

















Отзывы: