background image

CENTERPOINTE BUTCHER BLOCK COUNTERTOPS

Additional considerations should be made when 

installing a CenterPointe butcher block countertop 

around appliances and countertops with stove 

cutouts. Where appliances have heat acting on the 

countertop, such as dishwasher, under counter oven, 

or warming drawer, attach self-adhering aluminum 

flashing to the underside of the butcher block. This 

will assist in keeping heat and steam away from the 

block  and  cut  down  heat  transference.  The  fitting 

of cooktops must not restrict the countertop from 

expanding  and  contracting.  Ensure  that  there  is  at 

least 1/4” clearance all around the cooktop. To avoid 

splintering when cutting into the butcher block, it 

is recommended that masking tape be applied over 

the area that will be cut.

NOTE: Reapply finish to any areas that have been 

cut during installation.

3

KITCHEN APPLIANCE PLACEMENT

STEP 4 -

 CUT

To begin cutting using the circular saw, adjust the blade 

so that it extends 1/4” below the bottom of the butcher 

block countertop. A blade that hangs too low beyond 

the thickness of the wood may pull at the wood fibers, 

causing tears and splintering. Make the necessary cuts 

into the butcher block along the pencil line. Move the 

circular saw at a slow and even pace to ensure the blade 

does not tear the wood.

Note: If burn marks appear while cutting, sand the 

surface lightly with 120 grit sandpaper and re-apply 

finish.

EXAMPLE:
1-1/2”+1/4”= 1-3/4” BLADE DEPTH

SAW

COUNTERTOP 1-1/2” 

BLADE 1/4” BELOW

COUNTERTOP

SELF-ADHERING ALUMINUM FLASHING

UNDER-MOUNT APPLIANCE

Underside Front View

WALL

APPLIANCE

Overhead View

1/4”

1/4”

STEP 3 -

 TAPE & MARK CUT LINE

Carefully measure the width of the run of cabinets to be covered 

with butcher block, including any desired overhang, if applicable. 

After determining the necessary cuts to be made, draw the cut line 

boldly with a pencil, using a carpenter’s square to draw a straight 

line. Place a layer of masking tape over the pencil line. Press the 

masking tape firmly.

Overhead View

Содержание CenterPointe BUTCHER BLOCK COUNTERTOP








Отзывы: