Voxx Pursuit PRO9051E Скачать руководство пользователя

Страница: 2 / 16

128-9353

2 of 16

Page 2

Before You Begin

PROFESSIONAL INSTALLATION IS

STRONGLY RECOMMENDED

Roll down window to avoid locking the keys in the vehicle

during installation.

Avoid mounting components or routing wires near hot surfaces

or near moving parts like the steering wheel as it may prevent

proper operation of the vehicle.

Tape or loom wires under the hood and dash for protection as

well appearance

Use grommets when routing wires through metal surfaces to

prevent chafing and shorting.

Use a Digital Multi Meter for testing and verifying circuits. DO

NOT USE A "TEST LIGHT" OR "COMPUTER SAFE PROBE" as

these can set off air bags or damage sensitive vehicle computers

and electronics.

For technical support go to www.avxtech1.com

or call 1 800 225 6074

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that may cause

undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. Such modifications could void the user’s authority to operate

the equipment

Содержание Pursuit PRO9051E

















Результаты поиска

Содержание Pursuit PRO9051E

Отзывы:

Похожие инструкции для Pursuit PRO9051E

Бренды по названию

Популярные бренды

Voxx Pursuit PRO9051E, Инструкция по установке

Результаты поиска

Содержание Pursuit PRO9051E

Отзывы:

Похожие инструкции для Pursuit PRO9051E

Бренды по названию

Популярные бренды