Volvo TAD1240GE Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 68

background image

Diagnostic function

51

Code 4.3

Cause: Run-indication.

Response: None.

Corrective action:

•

Check the w

arning lamp

.

•

Check the wiring and connection to the run-indicator
w

arning lamp

.

Code 4.4

Cause: Overspeed warning lamp.

Response: None.

Corrective action:

•

Check the w

arning lamp.

•

Check the wiring and connection to the w

arning

lamp.

Code 4.5

Cause: Low coolant level warning lamp.

Response: None.

Corrective action:

•

Check the coolant level w

arning lamp.

•

Check the wiring and connection to the w

arning

lamp.

Code 4.6

Cause: Starter motor relay.

Response 1: Engine will not start.
The engine is to be started -> The engine turns over
immediately when the Power is switched on.
Response 2: The engine is running -> The starter motor
engages even though no start command was initiated.
The engine is being started -> The starter motor does not
disengage once the engine has started.

Corrective action:

•

Check the wiring to the relay.

•

Check that the relay is unbroken.

•

Check that the cable to the starter motor
(yellow/black cable) is connected correctly.

•

Check that the yellow/black cable is not damaged.

•

Check that the starter motor relay is unbroken.

Code 4.7

Cause: Start initiation EMS.

Response: Engine will not start. The engine can only be
stopped using the emergency stop on the engine.

Corrective action:

•

Check the wiring to the ignition key/button.

•

(Code 4.8 Stop input)

Code 5.1

Cause: Main relay.

Response: The instrument panel loses power when the
key is turned to start position. The engine will not start.

Corrective action:

•

Check the wiring to the relay.

•

Check that the relay is unbroken.

Code 5.2

Cause: Start initiation for CIU.

Response: The engine can not be started.

Corrective action:

•

Check the connections to the ignition key.

•

Check the wiring to the ignition key.

Code 5.3

Cause: Stop initiation for CIU.

Response: The engine can only be stopped using the
emergency stop on the engine.

Corrective action:

•

Check the connections to the ignition key.

•

Check the wiring to the ignition key.

«
...
51
52
53
54
55
...
»

Содержание TAD1240GE





































































Отзывы:

Нет отзывов

Похожие инструкции для TAD1240GE

Parilla Norswift 60cc

Бренд: IAME Страницы: 9

Parilla Norswift 60cc

Бренд: IAME Страницы: 35

Бренд: BONFIGLIOLI Страницы: 20

Бренд: Vascat Страницы: 9

Бренд: Shindaiwa Страницы: 48

EM-PMI540-T4000

Бренд: Danfoss Страницы: 71

Бренд: YS Страницы: 2

Бренд: Suzuki Страницы: 133

Бренд: WilTec Страницы: 6

Бренд: WilTec Страницы: 12

Бренд: DLE Страницы: 24

Бренд: Toyota Страницы: 185

Бренд: Stiga Страницы: 88

Бренд: Briggs & Stratton Страницы: 10

Бренд: Ober Страницы: 32

EMF SQML160 Series

Бренд: EMF Motor Страницы: 43

Бренд: Mitsubishi Страницы: 88

Бренд: powersoft Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды