Volvo B6324S Скачать руководство пользователя страница 17

Страница: 17 / 23

Enable condition

Minimum

Maximum

After start delay

20 s

Air flow

1.99 g/s

Engine coolant temp

60°C

110°C

Typical Fuel System diagnosis enable conditions

Malfunction criteria

Threshold value

Adaptive fuelling value above limit

> 1.24

for specified time

> 5 s

Adaptive fuelling value below limit

< 0.78

for specified time

> 5 s

Typical Fuel System diagnosis malfunction thresholds

Fuel system adaptation error

Monitor Strategy description

P0171

P0172

P0174

P0175

Lean fault, bank 1

Rich fault, bank 1

Lean fault, bank 2

Rich fault, bank 2

DTCs

Fuel system diagnostic operation

Corresponding MonitorID

To be able to activate closed-loop lambda control after

engine start the following must be true:

- Oxygen Sensor readiness detected (sensor

heating must be completed).

- No errors present for the Oxygen Sensor.

- The engine start sequence must be

completed (engine rpm risen close to idle).

- It is required that the engine is running.

- No catalyst damaging misfire detected.

- Not too big deviation of target lambda.

- Engine load not too low.

- No F/C (Fuel cut) recovery enrichment

effect.

Closed loop fuel trim

Содержание B6324S
























Результаты поиска

Содержание B6324S

Отзывы:

Похожие инструкции для B6324S

Бренды по названию

Популярные бренды

Volvo B6324S, Функциональное описание

Результаты поиска

Содержание B6324S

Отзывы:

Похожие инструкции для B6324S

Бренды по названию

Популярные бренды