manualshive.com logo in svg

Volvo Penta TAD420VE, Руководство по ремонту

Поделиться
Скачать
Volvo Penta TAD420VE Скачать руководство пользователя страница 82

Technical Data: TD/TAD720-722, TAD730/733, TAD750/760

80

Group 20

Exhaust gas temperatur

, approx:

At rated speed (standby power)

1)

: ..........................

1500 rpm

1800 rpm

TD720GE, TAD730GE: ...................................... 560°C 

(1040°F)

505°C 

(941°F)

TAD720GE, TAD731GE: .................................... 476°C 

(914°F)

433°C 

(837°F)

TAD722GE, TAD732/733GE .............................. 557°C 

(1035°F)

520°C 

(968°F)

At rated speed: .....................................................

1800 rpm

2100 rpm

2200 rpm

2300 rpm

TD720VE: .......................................................... 420°C

 (788°F)

—

—

—

TAD721VE: ........................................................ 420°C 

(788°F)

420°C

 (788°F)

425°C 

(797°F)

430°C

 (806°F)

TAD721VE: ........................................................ 490°C 

(914°F)

475°C 

(887°F)

480°C 

(896°F)

485°C 

(905°F)

TAD722/750/760VE: .......................................... 545°C

 (1013°F)

535°C 

(995°F)

540°C 

(1004°F)

545°C 

(1013°F)

1)

 

See in General information, Power standards.

2)

 

Information was not avaible at the time of printing.

Air intake

Air intake restriction, clean filter(s)

TD720GE/TAD720GE, TAD730GE: ................... 1 kPa

(0.14 psi)

TAD721GE/TAD722GE, TAD731-733GE: .......... 1.5 kPa

(0.22 psi)

TD720VE/TAD720/721/722/750/760VE: ............. 2.5

(0.36 psi)

Max allowed air intake restriction

TD720GE/TAD720GE, TAD730GE: ................... 3 kPa

(0.43 psi)

TAD721GE/TAD722GE, TAD731-733GE: .......... 3.5 kPa

(0.51 psi)

TD720VE/TAD720/721/722/750/760VE: ............. 6.5

(0.94 psi)

Intake and exhaust system

Turbocharger

, make and designation:

TD720GE/TAD720GE/TD720VE/TAD730GE: .............................. Schwitzer S2B
TAD720/721/722/750/760VE:
EPA 1: ......................................................................................... Schwitzer S2B
COM 2: ........................................................................................ Schwitzer S200
TAD721/722GE, TAD731–733GE ................................................ Schwitzer S200

Boost pressure at rated speed

1)

, ± 10%:

TD720GE, TAD730GE (1500 rpm): .............................................. 116 kPa

(16.8 psi)

TD720GE, TAD730GE (1800 rpm): .............................................. 131 kPa

(19.0 psi)

TAD720GE (1500 rpm): ................................................................ 136 kPa

(19.7 psi)

TAD720GE (1800 rpm): ................................................................ 142 kPa

(20.6 psi)

TAD721GE, TAD731GE (1500 rpm): ............................................ 161 kPa

(23.4 psi)

TAD721GE, TAD731GE (1800 rpm): ............................................ 175 kPa

(25.4 psi)

TAD722GE, TAD732/733GE (1500 rpm): ..................................... 178 kPa

(25.8 psi)

TAD722GE, TAD732/733GE (1800 rpm): ..................................... 200 kPa

(29.0

 

psi)

TD720VE: ....................................................................................

2)

 kPa

(

2) 

psi)

TAD720VE (EPA 1): .................................................................... 133

 

kPa

(18.9 psi)

TAD720VE (COM 2): ................................................................... 151

 

kPa

(21.9 psi)

TAD721VE (EPA 1): .................................................................... 155

 

kPa

(22.5 psi)

TAD721VE (COM 2): ................................................................... 163

 

kPa

(23.6 psi)

TAD722VE (COM2, High power): ................................................. 198kPa

(28.7 psi)

TAD750VE/TAD760VE: ............................................................... 198kPa

(28.7 psi)

Lube system: .................................................................................. Pressure lubrication
Max, permitted radial clearance (compressor side)

Schwitzer S2B: ............................................................................ 0.95 mm

(0.0374")

Schwitzer S200: ........................................................................... 0.88 mm

(0.0346")

Max, permitted axial clearance

Schwitzer S2B: ............................................................................ 0.14 mm

(0.00551")

Schwitzer S200: ........................................................................... 0.1 mm

(0.0039")

Max, allowed back pressure in exhaust line:

TD/TAD720GE, TAD721/722GE, TAD730-733GE (1500 rpm): ..... 5 kPa

(0.7 psi)

TD/TAD720GE, TAD721/722GE, TAD730-733GE (1800 rpm): ..... 7 kPa

(1 psi)

TD720VE, TAD720/721/722/750/760VE: ...................................... 7.5 kPa

(1.1 psi)

Содержание TAD420VE





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды