Volvo Penta D7A T Скачать руководство пользователя страница 93

Страница: 93 / 116

Replacing Battery

IMPORTANT:

Make sure that the new battery fulfills the specifications
in

Technical Data

. Read the information supplied with

the battery before you begin the installation.

IMPORTANT:

Do not disconnect the batteries with the engine
running.
Sensitive electrical components can be immediately
damaged.

WARNING!

Never confuse the positive and negative poles on the
batteries. Risk of arcing and explosion.

Disconnecting (A)

1 Untighten the nut and remove the – cable (black).

2 Untighten the nut and remove the + cable (red).

Remove the battery.

Connecting (B)

Place the new battery.

1 Connect the + cable (red) to the + pole on the

battery and tighten the nut.

2 Connect the – cable (black) to the – pole on the

battery and tighten the nut.

NOTICE!

Hand in the old battery to a re-cycling station.

Electrical Welding

Disconnect the positive and negative battery cables.
Then disconnect all the leads to the generator.

Always connect the weld clamp to the component
being welded and as close to the welding point as
possible. Never connect the clamp to the engine or
generator in such a way that current can pass across
a bearing.

IMPORTANT!

When welding has ceased, connect the leads to the
generator before reconnecting the battery cables.

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды