Volvo Penta D7A T Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 116

background image

After Engine Shutdown

•

Check the genset and engine room for leaks.

•

Close the fuel cock and seawater cock.

•

Read off the hour counter and carry out preventive
maintenance according to the maintenance
schedule.

•

Turn off the main switch if the genset is not to be
used for a long period.

IMPORTANT!

Never turn the power off using the main switch while
the genset is running. This can damage the alternator.

IMPORTANT!

Make sure the generator heater is working properly to
avoid condensation in the generator.

Anti-freezing measures

If the engine room cannot be protected from frost, the
seawater system must be drained and the coolant in
the freshwater system must contain sufficient anti-
freeze to prevent it from freezing. Refer to chapter

General, page 67

.

WARNING!

If the raw water system bursts due to freezing, the
vessel could sink.

IMPORTANT!

If the coolant does not give sufficient anti-freeze
protection, it may cause costly damage to the engine.
Check the charge of the battery. A poorly charged
battery can freeze and break.

Breaks in operation [not using the engine]

During periods out of service, when the boat is in the
water, the engine must be run warm once a fortnight.
This will prevent the engine from corroding.

IMPORTANT!

The engine must be conserved if it is not to be used for
longer than two months. Refer to chapter

Storage, page 92

.

Engine Shutdown

47713337 03-2021 © AB VOLVO PENTA

27

«
...
27
28
29
30
31
...
»

Содержание D7A T





















































































































Отзывы:

Нет отзывов

Похожие инструкции для D7A T

Бренд: Samson Страницы: 20

Бренд: Panasonic Страницы: 16

Бренд: BADODOSECURITY Страницы: 8

Бренд: Salda Страницы: 16

Бренд: Parker Страницы: 44

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Jabra Страницы: 4

Бренд: V2 Страницы: 48

Бренд: ACL Страницы: 20

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренд: Victaulic Страницы: 2

Бренд: National Instruments Страницы: 14

Бренд: Sturtevant Richmont Страницы: 73

Бренд: Zonex Страницы: 16

Бренд: Ravel Страницы: 33

Бренд: L&L KILNS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды