Volvo Penta D1 Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 92

background image

After Engine Shutdown

•

Check the engine and engine bay for leakages.

•

Close the fuel tap.

•

Close the sea cock where fitted.

•

Take an hour meter reading and carry out
preventive maintenance according to the
maintenance schedule.

•

Boats with stern drives: Trim the stern drive down to
maximum to protect the trim ram piston's untreated
surfaces from fouling.
If there is a risk of the boat striking bottom with the
stern drive, the drive must instead be trimmed up to
the maximum lift position.

•

Turn off the main switch before any long stoppage.

NOTICE!

Depending on the model and setup, there

could be more than one switch.

NOTICE!

Do not turn off the main switch within 30

seconds after turning off the ignition. This in order to
save engine data to the engine control unit.

Engine Shutdown

47711262 01-2019 © AB VOLVO PENTA

39

«
...
39
40
41
42
43
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов

Похожие инструкции для D1 Series

Бренд: Nacra Страницы: 28

Бренд: Barrus Страницы: 50

ALL-STAR 2101112

Бренд: O'Brien Страницы: 8

Бренд: Mercury Страницы: 50

Бренд: NW Explorations Страницы: 60

Бренд: SAFEQUIP Страницы: 20

SUN ODYSSEY 45DS

Бренд: Jeanneau Страницы: 146

Бренд: Jet Thruster Страницы: 22

Бренд: Yamaha Страницы: 28

Бренд: Yamaha Страницы: 133

BACKWOODS ANGLER 75

Бренд: Aquaglide Страницы: 28

Бренд: Supra Страницы: 60

Бренд: RowingSolutions Страницы: 20

Discovery T0191

Бренд: protech Страницы: 12

Бренд: PURSUIT Страницы: 146

Бренд: PURSUIT Страницы: 146

Бренд: PURSUIT Страницы: 144

S 408 SPORT 2017

Бренд: PURSUIT Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды